Abstract:Antimony selenosulfide, denoted as Sb2(S,Se)3, has garnered attention as an eco-friendly semiconductor candidate for thin-film photovoltaics due to its light-absorbing properties. The power conversion efficiency (PCE) of Sb2(S,Se)3 solar cells has recently increased to 10.75%, but significant challenges persist, particularly in the areas of open-circuit voltage (Voc) losses and fill factor (FF) losses. This study delves into the theoretical relationship between Voc and FF, revealing that, under conditions of low Voc and FF, internal resistance has a more pronounced effect on FF compared to non-radiative recombination. To address Voc and FF losses effectively, a phased optimization strategy was devised and implemented, paving the way for Sb2(S,Se)3 solar cells with PCEs exceeding 20%. By optimizing internal resistance, the FF loss was reduced from 10.79% to 2.80%, increasing the PCE to 12.57%. Subsequently, modifying the band level at the interface resulted in an 18.75% increase in Voc, pushing the PCE above 15%. Furthermore, minimizing interface recombination reduced Voc loss to 0.45 V and FF loss to 0.96%, enabling the PCE to surpass 20%. Finally, by augmenting the absorber layer thickness to 600 nm, we fully utilized the light absorption potential of Sb2(S,Se)3, achieving an unprecedented PCE of 26.77%. This study pinpoints the key factors affecting Voc and FF losses in Sb2(S,Se)3 solar cells and outlines an optimization pathway that markedly improves device efficiency, providing a valuable reference for further development of high-performance photovoltaic applications.

Accelerated Optimization of TiO2/Sb2Se3 Thin Film Solar Cells by High-Throughput Combinatorial Approach

Optimisation of Sb2S3 thin-film solar cells via Sb2Se3 post-treatment

Achievable efficiency improvement of Sb2Se3 thin-film solar cells through interface engineering

Interfacial engineering for high efficiency solution processed Sb2Se3 solar cells

Post-Treatment of TiO2 Film Enables High-Quality Sb2Se3 Film Deposition for Solar Cell Applications.

Sequential Coevaporation and Deposition of Antimony Selenosulfide Thin Film for Efficient Solar Cells

High-Throughput Screening and Optimization of Binary Quantum Dots Cosensitized Solar Cell

The Effect of Deposition Time Optimization on the Photovoltaic Performance of Sb2Se3 Thin-Film Solar Cells

Optimization Of Tio2 Photoanode Films For Highly Efficient Quantum Dot-Sensitized Solar Cells

An Optimization Path for Sb2(S,Se)3 Solar Cells to Achieve an Efficiency Exceeding 20

Efficient Sb2Se3 Sensitized Solar Cells Prepared Through a Facile SILAR Process and Improved Performance by Interface Modification

Improving the performance of Sb2S3 thin-film solar cells by optimization of VTD source-substrate proximity

An effective engineering with simultaneous carrier density enhancement and interface optimization enables efficient Sb2Se3 solar cells

Oxygen Content Modulation Toward Highly Efficient Sb2Se3 Solar Cells

Regulating Deposition Kinetics via A Novel Additive-assisted Chemical Bath Deposition Technology Enables 10.57%-efficient Sb2Se3 Solar Cells

Regulating Energy Band Alignment Via Alkaline Metal Fluoride Assisted Solution Post‐Treatment Enabling Sb2(S,Se)3 Solar Cells with 10.7% Efficiency

Molecular Induced Patching Process Improving Film Quality for High‐Efficiency Cd‐Free Antimony Selenosulfide Solar Cells

2,5-dichloro-3,4-diiodothiophene as a versatile solid additive for high-performance organic solar cells

Thermal diffused post-selenization for enhancing the photovoltaic performance of thermally evaporated Sb 2 Se 3 solar cell

A General Preparation Strategy for Hybrid TiO2 Hierarchical Spheres and Their Enhanced Solar Energy Utilization Efficiency

Se-Elemental Concentration Gradient Regulation for Efficient Sb2(S,Se)3 Solar Cells With High Open-Circuit Voltages