Abstract:The aim of this work was to investigate the challenges associated with bonding Al-Mg alloys and develop a new method for bonding these alloys to steels. During an extensive R&D project, over 80 attempts, using 11 methods, were made to bond Al-6 wt.% Mg alloy (Al-5056/Al-5A06) to two types of stainless steels (heat-resistant 1Cr18Ni9Ti and conventional 316). Wide ranges of temperature (500 °C to 580 °C), pressure (0.5 MPa to 10 MPa) and time (1 min to 2 h) were used when direct diffusion bonding of these alloys. Then, effects of using various interlayers and brazing foils were investigated. The interlayers used in this work were gallium, pure titanium, copper and aluminium foils, aluminium 6061 alloy sheets, aluminium-silicon brazing foils, zinc and zinc alloy foils as well as an active brazing foil (known as Incusil-ABA containing silver, copper, indium and titanium). Several complex and multi-stage processes, using up to 3 different interlayers in the same joint, were also developed and assessed. Examination and assessment of the bonded samples, including failed attempts, paved the way of developing new methods for bonding these dissimilar materials. A number of samples with tensile strengths from 200 MPa to 226 MPa were made by using complex combinations of 2 or 3 interlayers and triple-stage bonding cycles. The highest recorded bond strength was 226 MPa in the as-bonded condition. This value is above the measured yield strength (134 MPa) and about 93% of the measured ultimate strength (243 MPa) of the parent Al-Mg alloy after it was subjected to the same bonding cycle. Since the use of complex processes was not feasible for bonding large components, a simpler and more practical bonding cycle was also developed in the project. Using the simpler process, joints with tensile strengths around 90 MPa could be made. This article also sheds light on the difficulties associated with brazing and soldering aluminium alloys with a high magnesium content.

Contact-reaction Brazing of an AZ31 Magnesium/3003 Aluminum Alloy Using a Silver-Copper-zinc Interlayer

Interface Behavior of Brazed Joints of AZ31 Magnesium Alloy Using Silver-Base Alloy Interlayer

Interfacial structure of the joints between magnesium alloy and mild steel with nickel as interlayer

Study on process, microstructure and mechanical properties of 6061/AZ31 dissimilar metal joining with direct contact reaction brazing

An investigation on diffusion bonding of Mg/Al dissimilar metals using Zn-Bi alloy as interlayer

Joined AZ31B Magnesium Alloys with Ag Interlayer by Ultrasonic-Induced Transient Liquid Phase Bonding in Air

Contact Reactive Brazing of TC4 Alloy to Al7075 Alloy with Deposited Cu Interlayer

Joining mechanism, microstructure, and mechanical properties of AZ31/6061 joint prepared by pouring fusion welding process assisted with Zn-xSn brazing filler

Ultrasonic-assisted fluxless reactive bonding of Mg/Al dissimilar alloy using Zn–Al solder in air

Joining Mg Alloys with Zn Interlayer by Novel Ultrasonic-Assisted Transient Liquid Phase Bonding Method in Air

Microstructure and properties of joint for stirring brazing of dissimilar Al/Mg alloy during heating processes

Effect of Zn-brazed-interface on Microstructures and Mechanical Properties of Dissimilar 2A12/AZ31 Alloys Friction Stir Lap Welds

Friction stir welding between the high-pressure die casting of AZ91 magnesium alloy and A383 aluminum alloy

Ultrasound-Assisted Transient Liquid Phase Bonding of Magnesium Alloy Using Brass Interlayer in Air

Microstructure and Mechanical Properties of AZ31B/LY12 Joints Using Zn/Ag–Cu–Zn/Zn Multi-Interlayers via Ultrasound-Assisted Transient Liquid Phase Bonding

Wetting Behaviors of Al-Si-Cu-Mg-Zn Brazing Materials on 5083 Aluminum Alloy

Molecular Dynamics Simulations and Experimental Investigations of Atomic Diffusion Behavior at Bonding Interface in an Explosively Welded Al/Mg Alloy Composite Plate

Effects of Al/Zn interlayer on the solidification path and liquation cracking susceptibility of AZ31/ZK61 dissimilar magnesium alloy resistance spot welding joints

Ultrafast ultrasonic-assisted transient liquid bonding Al/Mg in air

Chemically dealloyed Mg–Cu alloy lamina as an interlayer for reinforcing a C/C composite – TC4 alloy vacuum brazed joint

Challenges and Latest Developments in Diffusion Bonding of High-Magnesium Aluminium Alloy (Al-5056/Al-5A06) to Stainless Steels