Abstract:Cu-3Ni-0.7Si-xCr-0.05Mg (x = 0.1 and 0.4) (wt% nominal composition) alloys were fabricated to investigate the effect of Cr contents on properties evolution and precipitation behavior of Cu-Ni-Si alloy. The results of the property analysis show that trace addition of 0.1 wt% Cr element contributes a better strength (ultimate tensile strength of 823 MPa) after single cold rolling and aging treatment. The precipitation behavior is characterized by transmission electron microscopy. It is found that nanoscale FCC structural Cr precipitates shift into submicron Cr 3 Si particles with Cr content increasing from 0.1 wt% to 0.4 wt%. Meanwhile, such superior formation of Cr 3 Si particle decreases the fraction of δ-Ni 2 Si owing to quick consumption of Si element from Cu matrix. Further quantitative analysis of various strengthening mechanisms reveals that the changed precipitation behavior notably affects their strengthening contribution to Cr contained alloys, resulting in an increase of more than 5.6% in the Orowan-Ashby mechanism. Surprisingly, in the case of the aging state at a temperature of 460 °C for a duration of 2 h, it is confirmed that although a much larger strengthening effect origins from nanosized δ-Ni 2 Si precipitate, the strength variation relies more on the Cr precipitation. That is, the lower strength at higher Cr content is mainly caused by the lower strengthening effect from Cr element related phases. In addition, the effect of the addition of trace Cr element on the operating mechanism on conductivity is also clarified. The results are expected to provide an appropriate content of Cr element and a dependable processing theory guidance for improving the comprehensive properties of the Cu-Ni-Si alloys.

Phase Transformation Behaviors and Properties of A High Strength Cu-Ni-Si Alloy

Accelerating Discontinuous Precipitation to Increase Strength by Pre-Deformation in Cu-Ni-Si Alloys

Revealing the Effect of Phase Composition and Transformation on the Mechanical Properties of a Cu–6Ni–6Sn–0.6Si Alloy

Combined experimental and computational investigation of precipitation behaviour and mechanical properties in a novel Cu–Ni–Si–Co alloy: effect of solution treatment temperature

Significantly enhanced high-temperature mechanical properties of Cu-Cr-Zn-Zr-Si alloy with stable second phases and grain boundaries

Excellent Mechanical Properties and High Electrical Conductivity of Cu-Co-Si-Ti Alloy Due to Multiple Strengthening

Microstructure and properties of high strength, high conductivity Cu-2.5Fe-0.3Cr-0.3Mg-0.2Si-0.1Ca-0.1Zr alloy treated by multi-stage thermomechanical treatment

Unveiling the Precipitation Behavior and Mechanical Properties in G-phase Strengthened CrFe2Ni2Ti0.2Six Multi-Principal Element Alloys

Microstructure and properties of Cu–Ni–Co–Si–Cr–Mg alloys with different Si contents after multi-step thermo-mechanical treatment

The Microstructure Evolution and Dynamic Recrystallization Mechanism of Cu-1.1–Ni-0.7–Co-0.45–Si-0.3Cr Alloys during High-Temperature Deformation

Microstructure and Property Evolution of Cu–9Ni–6Sn-xCr Alloys During Thermo-Mechanical Treatment Process

Simultaneously enhancing the strength and electrical conductivity of Cu-Ni-Sn alloy through plastic deformation of an intermetallic compound

Enhanced mechanical properties and strengthening mechanism of Cu-Ni-Si alloy with trace chromium addition

The strengthening role of micro-sized phases and nano-precipitates in Al–Mg 2 Si–Cu(–Ni) alloys at 25 °C and 350 °C

Effect of G-phase and heterogeneous deformation-induced strengthening on the mechanical properties of Cu-20Ni-20Mn-2Fe-1Si alloy

Precipitation behavior and microstructural evolution during thermo-mechanical processing of precipitation hardened Cu-Hf based alloys

Microstructure and Precipitate's Characterization of the Cu-Ni-Si-P Alloy

Transformation and Strengthening of Early Stage of Aging in Cu-3.2Ni-0.75Si Alloy

P phase precipitation and strengthening behavior of a novel polycrystalline Ni 3 Al-based intermetallic alloy at 1100 °C

On Novel Ni-rich Phase Formed During Aging of an Additively Manufactured Ultra-High Strength CoFeNi Alloy

Tailoring Formation and Proportion of Strengthening Phase in Non-Equiatomic CoCrFeNi High Entropy Alloy by Alloying Si Element