Abstract:Hydrogen storage in metal hydrides is a promising alternative to common storage methods. The surface of a metal hydride plays an important part in the absorption of hydrogen, since important partial reaction steps take place here. The development of surface contaminations and their influence on hydrogen absorption is examined by means of absorption experiments and surface analysis, using X-ray photoelectron spectroscopy (XPS), thermal desorption mass spectrometry (TDMS) and secondary neutral mass spectrometry (SNMS), in this work. All investigations were carried out on a modern AB(2) metal hydride alloy, namely Ti(0.96)Zr(0.04)Mn(1.43)V(0.45)Fe(0.08). Surface analysis (SNMS, XPS) shows that long-term air storage (several months) leads to oxide layers about 15 nm thick, with complete oxidation of all main alloy components. By means of in situ oxygen exposure at room temperature and XPS analysis, it can be shown that an oxygen dose of about 100 Langmuirs produces an oxide layer comparable to that after air storage. Manganese enrichment (segregation) is also clearly observed and is theoretically described here. This oxide layer hinders hydrogen absorption, so an activation procedure is necessary in order to use the full capacity of the metal hydride. This procedure consists of heating (T = 120 degrees C) in vacuum and hydrogen flushing at pressures like p = 18 bar. During the activation process the alloy is pulverized to particles of approximately 20 microm through lattice stretches. It is shown that this pulverization of the metal hydride (creating clean surface) during hydrogen flushing is essential for complete activation of the material. Re-activation of powder contaminated by small doses of air (p approximately 0.1 bar) does not lead to full absorption capacity. In ultrahigh vacuum, hydrogen is only taken up by the alloy after sputtering of the surface (which is done in order to remove oxide layers from it), thus creating adsorption sites for the hydrogen. This is shown by TDMS measurements with and without sputtering and oxygen exposure.

Surface Passivation of Aluminum Hydride Particles Via Atomic Layer Deposition

Surface Passivation of Metal Hydrides For Applications

Directed Stabilization by Air-Milling and Catalyzed Decomposition by Layered Titanium Carbide Toward Low-Temperature and High-Capacity Hydrogen Storage of Aluminum Hydride

Catalytically ultrathin titania coating to enhance energy storage and release of aluminum hydride via atomic layer deposition

Stability, reactivity and decomposition kinetics of surface passivated α-AlH3 crystals

Wet Chemical Synthesis of Non-solvated Rod-Like Α'-Alh3 As a Hydrogen Storage Material.

Dehydriding properties of γ-AlH3

Dehydrogenation Performances of Different Al Source Composite Systems of 2libh4 + M (M = Al, LiAlH4, Li3AlH6).

Synthesis and Stability of Hydrogen Storage Material Aluminum Hydride

Improved Hydrogen Generation from the Hydrolysis of Aluminum Ball Milled with Hydride

Hydrogen Desorption Behaviors of Γ-Alh 3 : Diverse Decomposition Mechanisms for the Outer Layer and the Inner Part of Γ-Alh 3 Particle

Aluminum hydride as a hydrogen and energy storage material: Past, present and future

Dehydriding Properties of Ti Or/and Zr-doped Sodium Aluminum Hydride Prepared by Ball-Milling

Reactivity and stabilization mechanisms of AlH3 crystals by coating of polyvinylidene difluoride

A new preparing method and performances of FeAl/Al2O3 tritium permeation barrier

Investigation on reversible hydrogen storage properties of Li3AlH6/2LiNH2 composite

Study on dehydrogenation and oxidation kinetics mechanisms of micron α-AlH3 in an oxidative atmosphere

Ultrathin Zirconia Passivation and Stabilization of Aluminum Nanoparticles for Energetic Nanomaterials via Atomic Layer Deposition

Influence of surface contaminations on the hydrogen storage behaviour of metal hydride alloys

Advanced preparation and processing techniques for high energy fuel AlH3