Abstract:The hot roll bending patchwork components of B1500HS uncoated ultra-high strength steel processed at industrial scale were welded with filler wire. The microstructure, grain orientation, mechanical properties and fracture behavior of the joint were investigated. The results showed that the weld metal (WM) was mainly composed of lath martensite and lower bainite (LB). Various microstructure appeared in different positions of the HAZ, among which martensite-austenite (M-A) constituents in the incompletely quenched zone and tempered martensite (TM) in the tempered zone were the key factors determining the performance of the joint. The welded joint exhibited complex structure and anisotropic mechanical response due to the decarburization and rolling texture of the original base material (BM). In the tempered zone, lath merge and boundaries disappear lead to the annihilation of dislocations, carbide precipitation leads to reduction of mobile dislocations, and recrystallization and recovery eliminate work hardening. The reduction of the effect of dislocation strengthening results in the formation of a softening belt at 6 mm from the center of the weld, with a minimum hardness of 266 HV. The tensile strength of the joint in the rolling direction (RD) was 983 MPa, and the fracture occurred in the softening belt. Both brittle and ductile fracture features were observed. The reason why the fracture occurs in the high temperature tempered zone instead of the incompletely quenched zone was the difference in the effect of "constraint strengthening". Fracture occurred through delamination cracking along the "weak interface" owing to precipitated high-hardness cementite particles and the unfavorably oriented ferrite cleavage planes.

Microstructure Transformation and Crack Sensitivity of WC-Co/steel Joint Welded by Electron Beam

Microstructure and mechanical properties of cemented carbide to steel joints by electron beam welding

Investigation on Microstructure of Electron Beam Welded WC-Co/40Cr Joints

Electron Beam Hybrid Welding-Brazing of WC-Co/40Cr Dissimilar Materials

In-situ investigation of microstructure-dependent deformation behavior of an electron-beam welded Ni Co based superalloy

Microstructures and phase composition of QCr0.8/1Cr21Ni5Ti joint by EBW with focus on steel side

Microstructural Characteristics and Mechanical Properties of an Electron Beam-Welded Ti/Cu/Ni Joint

Interfacial microstructure and mechanical properties of WC–Co/40Cr joints brazed at low–temperature with Ag–Cu–Ti + Sn novel filler

Investigation of cracks during electron beam welding of γ-TiAl based alloy

Investigating the effect of WC reinforcements in Cu Ti composite filler on the microstructural evolution and mechanical characteristics in brazing C f /SiC and GH3536

Microstructure and mechanical properties of electron beam welding of AlCoCrFeNi 2.1 eutectic high entropy alloy

Investigating the Effect of WC Reinforcements in Cu Ti Composite Filler on the Microstructural Evolution and Mechanical Characteristics in Brazing Cf/SiC and GH3536

Effect of a copper filler metal on the microstructure and mechanical properties of electron beam welded titanium-stainless steel joint

Microstructures and Mechanical Properties of Weld Metal and Heat-Affected Zone of Electron Beam-Welded Joints of HG785D Steel

Microstructure and Properties of WC–Co/3Cr13 Joints Brazed Using Ni Electroplated Interlayer

Microstructure and mechanical properties of butt joints of QCr0.8／1Cr21NiSTi equal-thickness dissimilar materials by electron beam welding

Investigation on process and microstructure of Ti/Ni/Cu joints by electron beam welding

Insights into microstructure evolution and fracture mechanisms of welded joints of high strength steel patchwork components

Research on microstructures and properties of electron beam welding joints of Ti-Ni-Cu

Crack formation and control upon the electron beam welding of TiAl-based alloys

Microstructure and mechanical properties of SiCp/Al joints by electron beam welding