Abstract:This paper presents a numerical approach to simulate sliding friction between engineering surfaces with 3D roughness in point contacts. The numerical approach is developed on the basis of the deterministic solutions of mixed lubrication, which is able to predict the locations where the asperity contacts occur, and the pressure distribution over both lubrication and contact areas. If the friction coefficients over the contacting asperities have been determined, total friction force between the surfaces can be calculated by summing up the two components, i.e., the boundary friction contributed by contacting asperities and the shear stress in hydrodynamic regions. The fi-ictions from asperity contact were determined in terms of a limiting shear stress or shearstrength of boundary, films while the fluid shear stress in the lubrication areas was calculated using different rheology models for the lubricant, in order to find which one would be more reliable in predicting fluid tractions. The simulations covered the entire lubrication, regime, including full-film Elastohydrodynamic Lubrication (EHL), mixed lubrication, and boundary lubrication. The results, when being plotted as a function of sliding velocity, give a Stribeck-type friction curve. This provides an opportunity to study friction change during the transition of lubrication conditions and to compare friction performance oil different rough surpces, which is of great value in engineering practice. Experiments were conducted on a commercial test device-universal material tester (UMT) to measure friction at a fixed load but different sliding velocities in reciprocal or rotary motions. The results also give rise to the Stribeck friction curvesfor different rough surfaces, which are to be compared with the results from simulations. The samples were prepared with typical machined surfaces in different roughness heights and textures, and in point contacts with steel ball. Results show that there is a general agreement between the experiments and simulations. It is found that surface features, such as roughness amplitude and patterns, may have a significant effect on the critical speed of transition firom hydrodynamic to mixed lubrication. It? the regime of mixed lubrication, rougher samples would give rise to a higherfiriction if the operation conditions are the same.

Influence Mechanism of Morphological Parameters on Tribological Behaviors Based on Bearing Ratio Curve

Effects of Surface Roughness on Sliding Friction in Lubricated-Point Contacts: Experimental and Numerical Studies

A Study of Tribological Performance Prediction Based on Surface Texture Parameters

Combined Effect of Boundary Layer Formation and Surface Smoothing on Friction and Wear Rate of Lubricated Point Contacts During Normal Running-in Processes

Discrimination of Wear Performance Based on Surface Roughness Parameters arithmetic mean height ( Sa ) and Skewness ( Ssk )

Effect of surface texture on the frictional properties of grease lubricated spherical plain bearings under reciprocating swing conditions

Wear model based on real-time surface roughness and its effect on lubrication regimes

Finite element simulation and experimental test of the wear behavior for self-lubricating spherical plain bearings

Study on Simulation of Coupled Heat Transfer, Stress and Wear Behavior in Pin-on-disc Experiments

Tribological mechanism of micro/meso/macroscopic textured surfaces under different normal forces, relative velocities, and sliding directions

Influence of Different Surface Texture Parameters on the Contact Performance of Piston Ring-Sleeve Friction Pair of Hydraulic Cylinders

Correlating numerical modelling with experimental studies to quantify the wear resistance of high-carbon chromium bearing steel in mixed lubrication

Research on Mixed Lubrication Problems of the Non-Gaussian Rough Textured Surface With the Influence of Stochastic Roughness in Consideration

Experimental research of sliding friction coefficient of rough surface under lubricated point contact

Tribological mechanisms of slurry abrasive wear

Frictional Behaviour of Engineering Surfaces in Overall Lubrication Regimes of Point Contacts

Analysis of the Rolling Interface Contact Characteristics in Mixed Lubrication Based on Gaussian Distribution Theory

Effect of surface roughness on sliding friction in lubricated contacts-reciprocal experiment study

Effect of compound pit textures on the friction and wear of thrust cylindrical roller bearings under starved lubrication

Modeling Contact of Rough Surfaces with Bearing Ratio Curves

Simulations And Measurements Of Sliding Friction Between Rough Surfaces In Point Contacts: From Ehl To Boundary Lubrication