Abstract:Most engineering surfaces possess topographies that are anisotropic. Some of the anisotropic surfaces are unintended result of machining process and others are by design for the purpose of lubricant retention or other considerations. Such is the case in problems involving piston liner and mechanical seal performance wherein the conformal contact of two rough surfaces is considered. It becomes critical to component performance to predict average contact pressure and gap between rough surfaces. Two of the well-known asperity-based statistical theories along with a deterministic method, based on Multi Level Multi Summation (MLMS) technique, are used to study the contact of nominally flat rough surfaces. The asperity-based statistical theories are GW model (Greenwood and Williamson, [1]), and its extension proposed by Chang, Bogy and Etsion [2], CEB model, for treating elastic-plastic contact. The contact examined is a set of nominally flat rough surfaces with a smooth flat. This study attempts to address two questions. The first concerns the effectiveness of asperity-based statistical theories in predicting average contact stress of rough surfaces with various degrees of topographic anisotropy. The second question involves the use of directional curvatures to ascertain the appropriateness of plane curvatures when degree of anisotropy is significant. To this end random surfaces are generated for five degrees of anisotropy including correlation length ratios 1, corresponding to an isotropic surface, and 3, 9, 36 and 81, corresponding to an increasing degree of geometric anisotropy. A module of Surface Distress Analytical Toolset (SDAT), for treating dry contact using deterministic approach with MLMS technique, is utilized to compute the contact pressure for these surfaces. This analysis constitutes ten surfaces for each correlation ratio resulting in fifty simulations of SDAT. For each correlation ratio statistical averages and variations of the maximum and mean contact pressures are found. Using the generated random surfaces, GW and CEB models are furnished with the parameters that include the standard deviation of summit height distribution, area summit density and six curvatures associated with asperity summit. These involve four directional curvatures that include curvatures along the x, y, positive diagonal, negative diagonal, and two equivalent curvatures, one based on spherical tip using average of the four diagonal curvatures and the other based on ellipsoidal asperity summit (Fig 1). The study suggests that GW and CEB typically overestimate average contact pressure. The mean pressures predicted using the largest directional summit curvature agrees most favorably with those predicted by SDAT. Surprisingly, agreement is most favorable for highest geometrical anisotropy. Both statistical methods seem effective in predicting mean gap between surfaces for moderate to low nominal pressures.

Discrimination of Wear Performance Based on Surface Roughness Parameters arithmetic mean height ( Sa ) and Skewness ( Ssk )

A Study of the Effect of Roughness on the Three-Body Wear Mechanism from a Microscopic Point of View: Asperity Peak Removal

A Study of Tribological Performance Prediction Based on Surface Texture Parameters

Study on the Mutual Influence of Surface Roughness and Texture Features of Rough-Textured Surfaces on the Tribological Properties

A Concept of the Effective Surface Profile to Predict the Roughness Parameters of Worn Surface

A parametric evaluation model of abrasive interaction for predicting tooth rough surface in spiral bevel gear grinding

Effect of Surface Roughness Parameters on Mixed Lubrication Characteristics

Surface roughness prediction in ball screw whirlwind milling considering elastic-plastic deformation caused by cutting force: Modelling and verification

Study of the surface generation mechanism and roughness distribution in internal spline shaping in consideration of tool wear

A Deterministic Mixed Lubrication Model for Parallel Rough Surfaces Considering Wear Evolution

The Quantitative Analysis of Surface Roughness in the Dry Friction

Research on Mixed Lubrication Problems of the Non-Gaussian Rough Textured Surface With the Influence of Stochastic Roughness in Consideration

Combined Effect of Boundary Layer Formation and Surface Smoothing on Friction and Wear Rate of Lubricated Point Contacts During Normal Running-in Processes

Modeling bulk modulus of abrasive cloth wheel and polished surface roughness for polishing blade with abrasive cloth wheel

Effects of Surface Roughness on Sliding Friction in Lubricated-Point Contacts: Experimental and Numerical Studies

An Efficient Numerical Model for Predicting the Torsional Fretting Wear Considering Real Rough Surface

Numerical Prediction of Surface Wear and Roughness Parameters During Running-In for Line Contacts under Mixed Lubrication

FEM computation of groove ridge and Monte Carlo simulation in two-body abrasive wear

Correlation Study of Functional Surface Parameters Based on Micro-Contact Analyses

An Assessment of Statistical Theory of Contact Between Macroscopically Conforming Rough Surfaces

Analysis, Modeling and Experimental Study of the Normal Contact Stiffness of Rough Surfaces in Grinding