The Application of C51 in the LCD Display

汤涛,孙志锋

DOI: https://doi.org/10.3969/j.issn.1001-4551.2002.05.012

2002-01-01

Abstract:The paper introduces the LCD controller-HD61202U of Hitachi corporation. And taking the LCM12864 of OCCULAR corporation in xiamen as an example, MCU AT89c51 is used as main controller chip to program the LCD display codes using c51.

What problem does this paper attempt to address?

The Design and FPGA Verification of TFT-LCD Timing Controller

CHEN Jin-long,HAN Yan

DOI: https://doi.org/10.3969/j.issn.1001-9146.2006.05.027

2006-01-01

Abstract:A design and FPGA verification of timing controller used in TFT-LCD system was introduced.A detail design of this controller was recommended according to the main ASIC design flow.Before synthesis,a particular step verifying the design of ASIC with FPGA was inserted,and a lot of experience data was available.
The Applications of RTX51 in Motion Control System

刘天泉,黄海,王树青

DOI: https://doi.org/10.3969/j.issn.1001-4551.2004.01.010

2004-01-01

Abstract:RTX51 which is a real-time system used in the single-chip microcomputer systems is introduced in this paper. We discuss the applications of RTX51 in motion control system, and give a hardware framework and a method of software design.
Control of LCD Module Based on PIC32MX MCU by Using Serial Port

Wang Jun,Geng Weidong,Zhang Fuhai,Xiang Guoqing,Song Penglin

DOI: https://doi.org/10.3969/j.issn.0465-7942.2011.06.005

2011-01-01

Abstract:The method of control 240128 lCD with built-RA8803 controller through serial port by PIC32MX microcontroller was described.How to use the serial port to transmit commands to LCD and the ways of use LCD to display texts,picutres and custom graphics were expounded in detail.The hardware connection diagram and key parts of the source code were given.Test results showed that this method could achieve the desired objectives.Seven I/O ports have been saved compared with drive directly by parallel ports.
Design of OLED Display Interface and Driver Based on SH1123

DING Wei-cheng,WANG Yi,LI Yuan-jing,WANG Min,FANG Fang

DOI: https://doi.org/10.3969/j.issn.1007-2780.2009.06.024

2009-01-01

Chinese Journal of Liquid Crystals and Displays

Abstract:This paper introduces the graphics dot matrix OLED display module based on the SH1123 drive,and then gives out the hardware interface circuit between the C8051F340 microprocessor and the module.Through a brief analysis of the SH1123 command system,the paper focuses on the realization of the underlying drivers of the module in the C language programming environment.It provides the realization of using keys to control the display menu.The OLED has good display effect and low power.So it is very suitable to the application which human-computer interaction interface shall has good display effect and low power requirements.
The Application of Multifunctional HMI and PLC in Control System of Beer Fermentation

肖杰,杨丽明,施丽莲,周泽魁

DOI: https://doi.org/10.3969/j.issn.1009-0134.2003.11.010

2003-01-01

Abstract:The application of multi-panel MP270 and S5/S7 PLC in the beer fermentation control, system is introduced in this paper with detailed explanation of hardware configuration and program design. Some tricks in software design and the communication approaches between S5 and S7 systems are presented in addition. This system has been in good condition since early 2002 till now.
Design of TFT-LCD Driver Circuits Based on S3C2410

刘立涛,罗嵘,金平

2006-01-01

Abstract:An LCD display system based on embedded processor S3C2410 and 3.5-inch TFT-LCD LTS350Q1-PE1 is proposed in this paper. Furthermore, theinterior principle of TFT-LCD is studied, TFT-LCD driver circuit is designed, and the structure and setting method of registers for S3C2410 LCDcontroller are illustrated.
The Design and Application of an Altimeter System Based on 89C52

YUAN Jie,HAN Bo,LI Ping

DOI: https://doi.org/10.3969/j.issn.1001-4551.2005.10.009

2005-01-01

Abstract:This paper accounts for the design problem of an altimeter system based on 89C52,which is an 8 bit microcontroller produced by ATMEL. Specially,it depends on the relationship between pressure,temperature and altitude.The most important points in this paper is that it uses the I/O in 89C52 to achieve the function of SPI,which makes the A/D function come true with TLC2543.Thereafter it transfers the data which is processed to the LCD,also it returns the data to the control computer through RS232.
Design and Implementation of Nios II-based LCD Touch Panel Application System

Song-Hai Zhang,Tong Zhang,Yicheng Yin,Wenju Ren

Abstract:This paper explains a system design for developing LCD touch panel applications by means of embedded system approach. Two Avalon-compatible IPs, acting as the LCD-display controller and the touch panel ADC controller are designed respectively for Nios II-centered SOPC. To verify the design, a game software named Lianliankan is developed on a SOPC containing the two custom IPs. The result indicates that the design has good usability, and satisfies the demand of application development better. Keywords— touch panel; Intellectual Property; Nios II; Avalon; system-on-a-programmable-chip (SOPC)

Computer Science,Engineering
Design and ASIC implementation of TFT color LCD controller

陈学峰,周荣政,洪志良

DOI: https://doi.org/10.3969/j.issn.1003-353X.2003.05.021

2003-01-01

Abstract:A design and ASIC implementation of the TFT color LCD controller used inadvanced digital camera are presented. Design requirement is introduced, then analysis and designof all blocks are presented in detail. The LCD controller consists of about 15000 gates and occupies0.49mm×0.80mm of silicon area in TSMC 0.25μm SAGETM technology.
A Method of Interactive Interface for Embedded ControIIer

吴波,许力

DOI: https://doi.org/10.3969/j.issn.1001-182X.2014.06.013

2014-01-01

Abstract:This paper proposes a generaI framework design for LCD muIti-IeveI menu,aiming at the design for interactive interface of controI er based on ARM.Then this paper puts forward a method for efficient keystrokes and interactive input,which can avoid traditionaI keys' jitter as weI as improve the utiIizationof I/O portby appIying touch keys,and take advantage of the structure variabIe in the C Ianguage to set the parameters.Themethod has got practicaI appIicationin the design of the ten-sion controI er system.
Speed Control Scheme of Large-LED Display Screen

Jingjing Zhou,Yan Wu

DOI: https://doi.org/10.2991/cmes-15.2015.49

2015-01-01

Abstract:Take MCS-51 series as an example, introduced a high-speed control scheme of single- chip solutions for large LED screen display.The control of SCM for LED display screen generally start read data from data memory then write the data to LED dot matrix tablets. The innovation of this program are that use a pair of read instruction of external data memory...
The desgin of LCD display backlight control system

Yan LI,Jun-jie LIU

DOI: https://doi.org/10.3969/j.issn.1000-5811.2015.02.032

2015-01-01

Abstract:Introduce a kind of micro controller STM32F030F4 as main control chip ,using LT3598 as the backlight of LCD driver display backlight control system .Through the BPW21 collection of the brightness of the external environment and the brightness of the dis‐play ,collected by signal feedback to the micro controller A/D ;the relationship between effi‐ciency and LED emission temperature ,drive temperature sensor DS18B20 module using the I2C micro controller ,detection of LED working environment temperature ,feedback to the microcontroller .The micro controller according to the brightness difference and temperature obtained using a control algorithm ,calculate the corresponding control variable ,the corre‐sponding output duty cycle PWM ,output current control LT3598 ,so as to form a closed loop control system ,will eventually reach the display brightness and the brightness of the envi‐ronment consistent goal .
Display and Drawing Methods for LCD Module

Chen Jianqun,Duan Chendong,Dong Penghui,Lu Wei

DOI: https://doi.org/10.16526/j.cnki.11-4762/tp.2009.04.013

2009-01-01

Abstract:More and more Intelligent instruments take LCD modules as their interface which can display Chinese characters Images and Curve.The paper takes TS12864-3/B as an example to introduce the Chinese characters and Images display method and some notations,studies the way of diplaying Real-time curve on LCD;the method is applied to a laser measurement and control instrument and get good effect.
SOPC Design on LCD Controller Based on NiosII

SONG Yue,LU Jun-ping,LEI Rui-ting,CHEN Wei,CHENG Bo

DOI: https://doi.org/10.3788/yjyxs20142901.0048

2014-01-01

Abstract:In order to realize SOPC controller design on TFT-LCD,IP core of TFT-LCD controller based on Nios II was designed by FPGA-EP4CE6F17C8and Verilog language.TFT-LCD controller was consisted of the Nios II soft-core processor,SDRAM controller,JTAG UART,LCD controller,Avalon bus for a full-color AT070TN84 TFT-LCD.Nios II soft-core processor was designed as core,IP cores such as SDRAM controller,TFT-LCD controller were connected to Nios II by Avalon bus,IP core design of TFT-LCD controller was mainly completed by such modules as the Avalon bus interface module,DMA module,FIFO module and the timing generator module. The color graphics display control wtih 800×480resolution,16bit color depth was achieved.Display experiment showed it was of stable,clear images,rich colors,no splash screen,wrong line and other phenomena,good visual effect.Design was of good configurability,reusability and portability.Practice proved that the SOPC design was effective.The design principle,control system simulation and experiment method,process were presented in the paper,relevant links of IP controller core design was mainly focused on at the same time.
Circuit Design of Single Panel Color LCOS Microdisplay Chip

LIU Yan-yan,DAI Yong-ping,GENG Wei-dong,SUN Zhong-lin

DOI: https://doi.org/10.3969/j.issn.1006-6268.2006.03.010

2006-01-01

Abstract:The circuit design of a single panel LCOS microdisplay chip is described. Equipped with proper engine and interface circuit system, the LCOS chip can be used to implement single panel LCOS rear-projection TV or other projection products. Similar with traditional field sequential color LCOS microdisplay chip, it consists of three parts: row scan driver, data driver and pixel array. The main difference of them is the row access method. The traditional field sequential color LCOS uses line-by-line row scan, while the LCOS introduced here uses random addressing. The red, green and blue data are almost written into the pixel array simultaneously. Cooperating with scrolling engine the color image is displayed. Single panel LCOS system costs less chips and relevant circuit systems, then can reduce product cost.
Research of wave display system based on 12864 LCD

Da-wei PAN,Pu HUANG

DOI: https://doi.org/10.3969/j.issn.1671-1041.2008.03.018

2008-01-01

Abstract:The paper presents a wave display system composed of C8051F005 MCU and 12864 LCD,and the system can sample and display all kinds of signals with complicated wave form.What's more it can measure and display the amplitude and frequency of the signal.
Design and Implementation of Multi-functional Display Controller Based on MPU and PC

张永强,邓少芝,许宁生

DOI: https://doi.org/10.3969/j.issn.1000-7180.2003.02.009

2003-01-01

Abstract:A display controller for matrix structural flat panel display devices is designed and carried out by single chip mi-cro-processor technique.With extended method of communica-tion to PC through RS-232C serial port,display image can im-mediately be controlled by mouse-clicking with friendly graphi-cal user interface.
Interfacing between MPU Rabbit2000 and LCD controller T6963c

SHEN Weixing,YU Tao,LIU Aimin,ZHENG Youyu,XIAO Bitao

DOI: https://doi.org/10.3969/j.issn.1006-6047.2008.10.025

2008-01-01

Abstract:The MMI(Man Machine Interface) of relaying protection,composed of LCD(Liquid Crystal Display) and high - performance RabbitCore RCM2200,is used to display and modify the information of protection CPU. The hardware design of the interface between RabbitCore RCM2200 module and VPG12864T LCD module with embedded T6963c controller is introduced with circuits and its direct control mode is presented. Read and Write operations are implemented using port E of RCM2200. The software of RCM2200 is programmed with Dynamic C of Z-World Corporation and the flowchart of VPG12864T parameter setting is presented. The Chinese characters are displayed in 16 ×16 pixels and the Chinese character base is generated by selecting the Chinese characters needed. The structure of Chinese character base and the flowchart of Chinese character display are proposed. The designed interface is feasible and efficient.
Implementation of LCD driver based on embedded Linux

GONG Li-li,ZHAO Yong

DOI: https://doi.org/10.3969/j.issn.1008-0570.2008.35.001

2008-01-01

Abstract:This article introduced the characteristic of Linux device driver, then accomplish LCD device driver in embedded Lin-ux2.6.14 system based on the s3c2410 platform.The article also illustrated how to compile the LCD driver module.
Dynamic Chinese Character Display Using Microcontroller-Based LED Dot Matrix Billboard

Ke Duan,R. A. Juanatas,Junduo Wang

DOI: https://doi.org/10.1109/RI2C60382.2023.10356037

2023-08-24

Abstract:In this research, the author leverages the advanced capabilities and technologies offered by the STC89C52RC controller to construct an electronic display incorporating multiple polar array modules. The primary focus of this display lies in its dynamic presentation of Chinese characters. The driver section design encompasses key components such as shift memory and registers, which play a crucial role in ensuring precise scanning of each line and column of text. To ensure smooth circuit operation, the inclusion of the 8550 transistors allows for effective current control, thereby amplifying current intensity and enhancing scanning efficiency. The software development process adopts a modular approach, facilitating the seamless implementation of the design concept. The software primarily facilitates data transmission to the display, enabling dynamic adjustment of the displayed text through control signals. Furthermore, specific software aids in character extraction, enabling the electronic display to manifest various dynamic effects, including vertical movement, when presenting static text. Rigorous experimentation validates the successful realization of dynamic text display functionality, with no observed ambiguities or performance fluctuations during the display process.

Engineering,Computer Science

The Application of C51 in the LCD Display

The Design and FPGA Verification of TFT-LCD Timing Controller

The Applications of RTX51 in Motion Control System

Control of LCD Module Based on PIC32MX MCU by Using Serial Port

Design of OLED Display Interface and Driver Based on SH1123

The Application of Multifunctional HMI and PLC in Control System of Beer Fermentation

Design of TFT-LCD Driver Circuits Based on S3C2410

The Design and Application of an Altimeter System Based on 89C52

Design and Implementation of Nios II-based LCD Touch Panel Application System

Design and ASIC implementation of TFT color LCD controller

A Method of Interactive Interface for Embedded ControIIer

Speed Control Scheme of Large-LED Display Screen

The desgin of LCD display backlight control system

Display and Drawing Methods for LCD Module

SOPC Design on LCD Controller Based on NiosII

Circuit Design of Single Panel Color LCOS Microdisplay Chip

Research of wave display system based on 12864 LCD

Design and Implementation of Multi-functional Display Controller Based on MPU and PC

Interfacing between MPU Rabbit2000 and LCD controller T6963c

Implementation of LCD driver based on embedded Linux

Dynamic Chinese Character Display Using Microcontroller-Based LED Dot Matrix Billboard