Abstract:Isobutylene-isoprene rubber (IIR)/polyamides 12 (PA12) blends are well known for their high gas barrier property and thus find applications in refrigeration hoses, tire inner liners, and so on. Nevertheless, the design and preparation of a good compatibilizer for the IIR/PA12 blend is required because of the poor compatibility between PA12 and the HR phases. In this study, an efficient reactive compatibilizer, glycidyl methacrylate (GMA)-grafted IIR (IIR-g-GMA) copolymer, and GMA/styrene (St)-grafted IIR (IIR-g-St-GMA) copolymer were produced through the free-radical melt grafting reaction, which were initiated by dicumyl peroxide (DCP). Compared with IIR-g-GMA, IIR-g-St-GMA shows a significantly higher grafting degree because the fast generated, more stable St-grafted HR macroradicals can act as a "bridge" to connect GMA molecules on IIR macroradicals. The results indicate that reactive compatibilization occurs by the introduction of the copolymer, and the extent of the interfacial reaction and compatibilization effect increases with increasing the copolymer content and the grafting degree of GMA. Nanomechanical mapping images of atomic force microscopy show that the average interfacial thickness of the blend largely increases from approximately 55 to 120 nm after compatibilization with 30 phr IIR-g-St-GMA. Meanwhile, the size of the IIR dispersed phase domains largely decreases from 3 to 5 mu m to approximately 0.7 mu m after compatibilization with this copolymer. The compatibilization mechanism of the copolymers on IIR/PA12 blends is discussed.

Effect of blending ratio on properties of EPDM/IIR inner tube

The Effect of Blending Ratios on Properties of EPDM/POE Blends

Visualization of Poly(ether Imide) and Polycarbonate Blending in an Internal Mixer

Study on Rheological Properties of Reactive PP/EPDM Blends

Structure and Properties of OC/IIR/EPDM Nanocomposites Prepared by Melt Blending

The Blending,Curing Behavior and Properties of Several Synthetic Rubbers

Effect of the Blending Process and Filler Loading on the Mechanical Properties of Silica-Filled Sbr/Br Compounds

Effect of Epoxidized EPDM on Structure and Properties of PBT

Effect of compatibilizer on the performance of SBR/EPDM blend system

Effect of Reactive Plasticizer LIR on Properties of NR/BR Blend

Constituent compatibility and physical properties of bio‐based EUG/EPDM blends

THE STUDY ON SOME PROPERTIES OF SUPER ELASTORMER EPDM／PA

Effects of Compatibilizing Agent and in Situ Fibril on the Morphology, Interface and Mechanical Properties of EPDM/nylon Copolymer Blends

The Morphology and Property of Ultra‐fine Full‐vulcanized Acrylonitrile Butadiene Rubber Particles/epdm Blends

Study on the effect of wet mixing process on the properties of EPDM rubber/fiber/hollow glass microsphere composite system

Correlations between H2 Permeation and Physical/Mechanical Properties in Ethylene Propylene Diene Monomer Polymers Blended with Carbon Black and Silica Fillers

Effect Of Interfacial Enhancing On Morphology, Mechanical, And Rheological Properties Of Polypropylene-Ground Tire Rubber Powder Blends

Crosslink Network Evolution of BIIR/EPDM Blends During Peroxide Vulcanization

Grafting of Isobutylene–Isoprene Rubber with Glycidyl Methacrylate and Its Reactive Compatibilization Effect on Isobutylene–Isoprene Rubber/Polyamides 12 Blends

Morphologies and Mechanical Properties of Cis-1,4-Butadiene Rubber/Polyethylene Blends

Preparation and Properties Research of Oil-absorbing Rubber