Abstract:Multi-phase compatibilizers are potentially attractive, not only for the preparation of ternary or multi-phase immiscible polymer blends with high performance, but also for recycling and reuse of waste plastics mixture. In this study, the maleic anhydride (MAH) and styrene (St) dual monomers grafted PP, PP-g-(MAH-co-St) is prepared as a multi-phase compatibilizer, which exhibits highly effective compatibility on the PP/PA6/SEBS (70/15/15) ternary blends. Scanning electron microscopy (SEM) reveals that, with increasing the compatibilizer, the morphology evolves from the individual PA6 particle encapsulated by SEBS to several smaller-size PA6 particles partially encapsulated by SEBS phase, then to the tiny PA6 particles and some larger-size SEBS agglomerates predominantly dispersed separately in PP matrix. The morphology development predicted by spreading coefficients shows a consummate consistency with that observed by SEM. Moreover, the good compatibilization and corresponding morphologies result in superior enhancement of mechanical properties. Compared to the uncompatibilized blend, adding 15 wt multi-phase compatibilizer to the blend leads to the best mechanical properties with the yield stress, stress at break, strain at break and impact failure energy improved significantly by 23%, 132%, 647% and 220%, respectively. The results verify that the domains with small-size PA6 particles (03-0.4 mu m) partially encapsulated by SEBS (0.5-0.7 mu m) in PP matrix are very effective to enhance the mechanical properties of the blends. The morphologies of large-size PA6 particles encapsulated by SEBS or tiny PA6 particles and some larger-size SEBS agglomerates dispersed separately in PP matrix for the enhancement in mechanical properties of the blends are very limited. Consequently, the enhanced interfacial interactions and the morphology with the rigid particles partially encapsulated by a rubber-like phase in matrix are crucial for the ternary polymer.blends. (C) 2016 Elsevier Ltd. All rights reserved.

Study on PA/PVC/NBR Ternary Blending Elastomer

Rheological Properties of PET/PA66/Liquid Crystalline Copolyesteramide Blends

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Mechanical And Tribological Properties Of Paws Blends

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

Mechanical and Tribological Properties of PA/PPS Blends

Ternary blends from biological poly(3-hydroxybutyrate-co-4-hydroxyvalerate), poly(L-lactic acid), and poly(vinyl acetate) with balanced properties

Dao Dian Ju Yi Que - Dan Xing Ti Fu He Mo

Study on compatibility of hydrogenated nitrile rubber and perfluoromethylvinylether(PMVE) rubber

Ternary Blends from Biological Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate), Poly(propylene carbonate) and Poly(vinyl acetate) with Balanced Properties

Morphology Development and Superior Mechanical Properties of Pp/Pa6/Sebs Ternary Blends Compatibilized by Using A Highly Efficient Multi-Phase Compatibilizer

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends

Miscibility, crystallization and mechanical properties of poly[(3‐hydroxybutyrate)‐ co ‐(4‐hydroxyvalerate)]/poly(propylene carbonate)/poly(vinyl acetate) ternary blends

Preparation and Properties of PA10T/PPO Blends Compatibilized with SEBS-g-MAH

Sustainable and high‐performance ternary blends from polylactide, CO 2 ‐based polyester and microbial polyesters with different chemical structure

Polymer Blends of Pbt and Pp Compatibilized by Epoxidized Ethylene Propylene Diene Rubber

Polypropylene/polypropylene-grafted acrylic acid copolymer/ethylene–Acrylic acid copolymer ternary blends for hydrophilic polypropylene

Preparation of fully cross-linked CNBR/PP-g-GMA and CNBR/PP/PP-g-GMA thermoplastic elastomers and their morphology, structure and properties

Effect of Mixing Sequence on Phase Morphology and Mechanical Properties in Polyamide 6/butadiene (core) Styrene Acrylonitrile-G-Maleic Anhydride (shell) Latex/Organoclay Ternary Nanocomposites

Compatibilization And Toughening Of Immiscible Ternary Blends Of Polyamide 6, Polypropylene (Or A Propylene-Ethylene Copolymer), And Polystyrene