Abstract:Journal of Thermoplastic Composite Materials, Ahead of Print. This interesting study investigated the effect of Maleic Anhydride-grafted-Polypropylene/Epoxidized Natural Rubber (PP-g-MA/ENR) as a compatibilizing agent (CA) on the properties of a 30/70 Polypropylene/Natural Rubber PP/NR blends. The effect of dynamic vulcanization with sulfur-donors (i.e.: Tetramethyl thiuram disulfide (TMTD) and 4,4 Dithiodimorpholine (DTDM)) which were used as vulcanizing agents was also reported. Several formulations of TPVs with different concentrations of CA (from 5 to 15 phr) were prepared by mixing in the molten state using a Haake Rheocord 90. The structural analysis of dual compatibilizer was examined by FTIR spectroscopy. The rheological behavior was examined using Haake Rheocord 90. The mechanical properties were determined by the tensile measurements. The dynamic mechanical thermal properties were investigated by DMA. A morphological examination was conducted using SEM Microscopy, respectively. FTIR analysis confirmed reactions between the MA group in PP-g-MA and the epoxy groups in ENR, resulting in ENR-grafted PP with an ester and acid-based linkage. The Haake plastograms revealed a proportional increase in the final mixing torque value with the increasing content of CA. The mechanical results exhibited higher values in terms of tensile strength and Young's modulus for the TPVs containing CA compared to un-compatibilized ones. The compatibilized TPV blends exhibited a noteworthy increase in storage modulus and a notable decrease in loss tangent values with the CA concentration increased. Furthermore, the TPVs show two distinct-phase morphologies. That is, the TPV with CA showed the presence of smaller vulcanized rubber particles dispersed within the PP matrix, a phenomenon that becomes more pronounced with higher CA contents.

Study on compatibility of hydrogenated nitrile rubber and perfluoromethylvinylether(PMVE) rubber

Enhanced Compatibility and Thermo-Oxidative Stability of Silicone Rubber/Ethylene–Propylene Terpolymer Composites Via in Situ Interface Coupling

Research on Mechanical Properties, Compatibility, Flame Retardancy, Hot-Air Ageing Resistance of Hydrogenated Nitrile-Butadiene Rubber/Chloroprene Rubber Blends

The effect of physical compatibilization and dynamic vulcanization on the properties of thermoplastic vulcanizates derived from polypropylene and natural rubber blends

Studies of Latex Blends of Natural Rubber/poly(methyl Methacrylate-Co-2-ethylhexyl Methacrylate) and Their Comparison with Incompatible Natural Rubber/poly(methyl Methacrylate)

Study on the Preparation of Macromolecular Compatibilizer and Its Effect on the Characteristics of Fluoroelastomer (fkm)/silicone Rubber (MVQ) Blend

Study on NBR/PP Blend Compatiblized by TETA/MP/XNBR

Study on compatibilization of EPDM/PP TPV

Effect of the Compatibility on the Morphology and Properties of Acrylonitrile–butadiene Rubber/polypropylene Thermoplastic Vulcanizates

Effects of compatibilities on the properties of polyvinyl chloride/nonpolar rubbers blends

Study on PA/PVC/NBR Ternary Blending Elastomer

Polyamide Reinforced Epdm Compatibilized with Maleic Anhydride Grafted Ethylene-Propylene-Diene Rubber

Compatibility and Nonlinear Viscoelasticity of Polychloroprene/polyvinyl Chloride Blends with Nitrile Butadiene Rubber As a Compatibilizer

Compatibilization of Fluororubber/ Silicone Rubber Blends by the Incorporation of 2,2,2-Trifluoroethyl Methacrylate Grafted Silicone Rubber

Studies on Self-Vulcanizing Fluoroelastomer/Phenol Hydroxy Silicone Rubber Blends

Excellent Compatibilization Effect of a Dual Reactive Compatibilizer on the Immiscible MVQ/PP Blends

Effect of compatibilizers on dynamic vulcanized chlorinated butyl rubber/polyamide 12 thermoplastic elastomers

Effects of Compatibilisers on the Properties of Polyvinyl Chloride/Nonpolar Rubbers Blends

A method to essentially increase the compatibility of thermoplastic polyurethane/methyl vinyl silicone rubber based thermoplastic vulcanizate

Constituent compatibility and physical properties of bio‐based EUG/EPDM blends