STUDY OF ROLLING FORCE MODEL ON HOT STRIP MILL

刘文仲,吕志民

DOI: https://doi.org/10.3321/j.issn:0449-749x.2002.05.011

2002-01-01

Abstract:The rolling force models used in computer control system of hot strip mill are evaluated According to the experience, a new analytic method of rolling force model is presented which is easy

What problem does this paper attempt to address?

ANALYSIS AND MODIFICATION OF HYDRAULIC ROLLER BENDING FORCE CONTROL SYSTEM

陈为国,陈章位,丁凡,吴根茂

DOI: https://doi.org/10.3321/j.issn:0449-749x.2001.11.011

IF: 1.7031

2001-01-01

Ironmaking & Steelmaking

Abstract:A mathematical model was put forward for the hydraulic roller bending force control system of Baosteel's hot strip rolling mill A hydraulic mechanical filter was built in this control system to eliminate damage of roller bending force sensors The device satisfactorily protects the sensor from hydraulic impact and the control precision was improved
Analysis of Rolling Force Model in Cold Rolling Mill

Y. Li,Z. Jiang,F. Li

DOI: https://doi.org/10.1051/metal/2009016

2009-01-01

Abstract:A rolling force model of continuous cold rolling mill based on elastic and plastic mechanics was developed and successfully applied in the control system of a 1420 mm cold rolling mill in Baosteel. Considering simplicity and practicability of calculation, stress of elastic zone and plastic zone during the cold rolling process was calculated and analyzed by incorporated simple finite element method and recursive calculating method. Compared with the measured rolling force, the results of the rolling force model are beyond 96.5%. A method for optimizing rolling force by improving reduction, dimension, coefficient of friction, deformation and tension is put forward.
Analysis of Feasibility for Rolling Force Model Optimization of Hot Strip Mill of Jinan Iron & Steel Group Corporation

YANG Gui-ling,BAI Yan,GUO Li-ping,GUO Hong-wei,LI Long,DING Hua

DOI: https://doi.org/10.3969/j.issn.1671-6620.2006.04.016

2006-01-01

Abstract:The rolling force model from 1700 hot strip mill of Jinan Iron Steel Co. has been analyzed, which is calculated by using the cycling calculation method and the effects of chemical composition, deformation temperature and strain rate on the deformation resistance have been investigated. The model was experimentally verified integrating with the practice in hot strip mill of Jinan Iron Steel Go. Optimized model was founded by putting in self-studying coefficient. The precision of the model can meet the requirement for application but more work must be done to optimize the coefficients in the models for producing other new types of steels.
STUDY ON ROLL WEAR ON HOT STRIP ROLLING MILL

CHEN Liansheng,Lian Jiachuang

DOI: https://doi.org/10.3321/j.issn:0449-749x.2001.01.017

2001-01-01

Abstract:This paper describes the mechanism and distribution of roll wear on hot strip rolling mill, including some factors effecting on roll wear and the problems in some roll wear prediction models. Suggestions for improvement are put forward.
On the Optimization of a Rolling-Force Model for a Hot Strip Finishing Line

Jingcheng Wang,Chunzhao Chen

DOI: https://doi.org/10.1016/j.isatra.2007.02.008

IF: 7.3

2007-01-01

ISA Transactions

Abstract:This paper starts with a profound analysis of rolling-force calculation models of two hot strip rolling product lines. According to classical theory of rolling-force calculation, the structure of rolling-force calculation model is firstly optimized. Then with application of data mining techniques, including clustering sampling approach and optimization algorithm, to the field data from product line, the value of key coefficients of the model is adjusted. By the proposed optimization scheme, a better rolling-force prediction is achieved.
An analytical model of plate rolling force with a simple available velocity field and equal perimeter yield criterion

Li Wang,Xiaoyan Zhu,Dewen Zhao,Dianhua Zhang

DOI: https://doi.org/10.1177/1687814017728837

IF: 2.1

2017-09-01

Advances in Mechanical Engineering

Abstract:To analyze plate rolling force, a simple available velocity field is first proposed in this article. Based on the velocity field, the internal deformation energy rate and the friction energy rate are analyzed by the equal perimeter yield criterion and the method of the collinear vector inner product, respectively. Finally, the rolling force accounting for the elastic flattening of the roller and the temperature rise of the rolled piece are ultimately obtained through the minimization of the total energy rate. The theoretical rolling forces are compared with actual measured data, and a good consistency is found since the maximum error between them is less than 4.7%. In addition, the discussion of different rolling conditions, such as friction factor, thickness reduction, and shape factor, upon rolling force, location of neutral angle, and stress state coefficient is also carried out.

engineering, mechanical,thermodynamics
Rolling Process Analysis of Working Rollers of Cold Rolling Mill Based on ANSYS

Kun Shi,Gang Zheng,Jianhua Hang

DOI: https://doi.org/10.1088/1742-6596/1624/2/022049

2020-10-01

Journal of Physics: Conference Series

Abstract:Abstract Aiming at the complex changes of the working rollers and rolled pieces in the rolling process of a cold rolling mill, this paper built a finite element model of the working rollers and rolled pieces based on ANSYS, and analyzed the rolling process of working rollers by using the transient algorithm of structural dynamic equation. The stress-strain situation and rolling force curve of working rollers and rolling pieces were obtained, The results revealed the characteristic change process of working rollers and rolled pieces in the rolling process, which layed the foundation for further realizing the precise control of the rolling process of cold rolling mill.
Analytic Numerical Modeling for Thermal Mechanical Processing of Plate under Rolling

ZS Cui,BY Xu,XY Ruan

DOI: https://doi.org/10.1063/1.1766565

2004-01-01

AIP Conference Proceedings

Abstract:In order to predict the microstructures of the hot‐rolled plate product, an analytic numerical model for plate under hot rolling is presented. In the method, the analytic expressions of temperature, rolling pressure and strain rate are derived from corresponding governing differential equations and evaluated by numerical techniques, and the solutions are incorporated with the mathematical model of microstructure evolution. The model is verified by a simulation of an experimental aluminum plate hot rolling and employed to simulate an industrial 13‐pass rolling of Q235B steel plate with spray descaling and on‐line cooling. Some computed results are compared with measured data, and good coincidences are obtained. Compared with finite element method, the model takes very short time in computation and can be easily applied to simulate multi‐pass rolling.
Research progress and intelligent trend of accurate modeling of rolling force in metal sheet

Shun-hu Zhang,Yi Zhang,Wei-gang Li,Wen-hao Tian,Yan Li,Li-zhi Che

DOI: https://doi.org/10.1007/s42243-023-01067-4

2023-09-23

Journal of Iron and Steel Research International

Abstract:The rolling force model is the basis for reasonable selection of rolling equipment and optimization of rolling process, and the establishment of an accurate mathematical model as well as doing the corresponding parameter analysis has been the focus of research in this field for many years. Different modeling methods of the rolling force and their research progress were introduced, the main methods of which are the theoretical analysis, the finite element simulation, the artificial neural network modeling, the hybrid modeling of theory and neural network, as well as the hybrid modeling of finite element and neural network. Meanwhile, the application examples of rolling force models in thickness control, strip crown control, and schedule optimization were presented, and an outlook on the new directions of future development was made, including establishing new type of hybrid models, solving the black box problem, and realizing the multi-objective optimization accounting for some special requirements.

metallurgy & metallurgical engineering
Study on Rolling Force during Asymmetric Rolling Process

张杏耀,付斌,单爱党,金国

DOI: https://doi.org/10.3969/j.issn.1671-7333.2012.01.010

2012-01-01

Abstract:Using finite element method（FEM）, asymmetric rolling process was simulated and the rolling force was analyzed. The simulated results were in good agreement with analytical results. The simulated results showed that rolling force decreased to a stable value as the speed ratio increased. It is of great importance to the design of asymmetric rolling mill and setting down of rolling schedules.
Modelling of axial thrust force between rolls in strip mill

Shuilin Lin,Qinghua Song,Chao Ma,Jianliang Sun,Marian Wiercigroch

DOI: https://doi.org/10.1016/j.ijmecsci.2024.109190

IF: 7.3

2024-03-12

International Journal of Mechanical Sciences

Abstract:Theoretical predictions and engineering practice indicate that roll crossing in strip mills can generate an excessive axial thrust force between rolls, often resulting in roll bearing failures and a lower strip surface quality. Although this effect is important in design of strip mills and manufacturing, the existing literature refers only to simple formulas and manual measurements for evaluating this axial thrust force. In this work, a novel approach to model the axial thrust force considering tangential deformations of the rough surface layer and the matrix is proposed to calculate the axial thrust force for various typical strip mills. In addition, data from an industrial test rig at the production site taken to examine the real-time axial thrust force during roll crossing. The results indicate that under light load conditions, the axial thrust force can be accurately predicted by considering only the tangential deformation of the rough layer surface, whereas for heavy loads conditions, the tangential elastic deformation of the matrix must be taken into account as well. The axial thrust force approaches sliding friction force limit for crossover angles smaller than 0.1°. In general, the axial thrust force grows with increasing crossover angle, which is confirmed by both theoretical and experimental results.

engineering, mechanical,mechanics
Research on the analytical model of rolling force for TiAl alloy pack rolling

Zhanrui Wang,Guangyao Tang,Zhenyao Lei,Haijun Wang,Zhiqiang Xu,Hui Yu

DOI: https://doi.org/10.1051/metal/2023086

IF: 0.9461

2024-01-14

Metallurgical Research & Technology

Abstract:Pack rolling is a hot rolling process for metals with poor plastic forming. The rolling force model is an important model for pack rolling process. Based on the E. Orowan differential equation and the characteristics of pack rolling process, the analytical model of rolling force for pack rolling process was established. Based on the established rolling force model, the influence of roll diameter, reduction rate, metal layer thickness ratio and shear yield stress ratio on the distribution of rolling stress, neutral angle and connection angle was studied. The results indicate that as the increase of reduction rate and shear yield stress ratio, and the reduction of metal layer thickness ratio, the middle layer metal is more prone to plastic deformation. The basic assumptions of the analytical model were verified through a three-dimensional finite element model. The outer layer metal and the middle layer metal were selected as 304 stainless steel and Ti-Al-2Cr-2Nb alloy for pack rolling experiments, respectively. The error between the calculated results of the analytical model and the experimental results is within 15%. The analytical model of rolling force can accurately predict the rolling force and provide theoretical guidance for the formulation of the pack rolling process.

metallurgy & metallurgical engineering
Research on Mathematical Model of Loading Roll Gap for Strip Temper Mill

DUAN Xue-hou,WANG Shi-gang,TANG Cheng-long,XU Wei

DOI: https://doi.org/10.3969/j.issn.1003-9996.2011.01.014

2011-01-01

Abstract:Combinating parameter modification and nonlinear regression analysis,the model of loading roll gap was established according to the characteristics of strip with thin gauge and low percent reduction during tempering. The results showed that the model could meet the practical rolling situation which had high accuracy and little error,and could forcast the shape exactly.
Simulation of the rolling process of 4-high hot steel strip continuous mills

Yingrui Wang,Zhenshan Cui,Hongmin Liu

IF: 1.8

2004-01-01

Materials Science and Technology

Abstract:The three-dimensional plastic deformations of strip are analyzed by using the stream surface strip element method, the elastic deformations of rolls are analyzed by using the influence coefficient method, the analyzing and computing model of shape and crown of 4-high mill is established by combining them, and the rolling process of 1660 mm 4-high hot steel strip continuous mills is simulated. The simulated results tally well with the experimental results. The model and the method for simulation of shape analysis and control of 4-high hot steel strip continuous mills are provided.
Mathematical Models of Stable Roll Load of Double Stands Thin Gauge Strip Temper Mill

TANG Cheng-long,WANG Shi-gang,LIANG Qin-hua,GU Tin-quan,XU Wei

DOI: https://doi.org/10.3321/j.issn:1006-2467.2009.01.005

2009-01-01

Abstract:Aiming to solve the difficulties in calculating the stable roll load of tempermill which is especially used to dryly temper thin-gauge strip with the small reduction,an improved roll model and torque model were proposed on the basis of hypothesis of flat plate compression.The roll model includes two(experiential) sub-models: equivalent deformation length and deformation assistance and the torque model is(linearly) corrected especially considering the tension effects.The comparison between the actual and calculated results shows that the models possess high precision and the hypothesis is reasonable.(Finally,) the key parameters relative to the roll load of a new establishing double stands temper mill were checked via the new developed models,which displays the models have the value of applications in real(projects.)
Shape and Crown Control Strategy for PC Mill

王雪松,张跃飞,田士平,董占斌

DOI: https://doi.org/10.13228/j.boyuan.issn0449-749x.2012.11.004

2012-01-01

Abstract:According to the characters of PC hot strip mill,the PC mill shape and crown predictive model was established to simulate the rolling process of PC mill through using differential method to solve the metal plastic deformation and using influence function method to solve elastic deformation of rolls.The roll-bending force and cross angle control characteristics of PC mill were analyzed,and the corresponding control strategy was given out.The results show that in the whole process of shape setting control,the cross angle has more ability to control shape and crown,but the roll-bending has great impact on distribution force between rolls.Through the reasonable setting and distribution,it will reduce the non-uniform coefficient of distribution force between rolls and the effect of shape control is more favorable.
Numerical Analysis on Flatness Adjusting Performance of Hot Wide Strip Temper Mill with Small-Diameter Work Rolls

Hui Li,An-rui He,Jian Shao,Chi-huan Yao,Jian Zheng,En-rui Wang,Zhi-hong Zhang

DOI: https://doi.org/10.1080/03019233.2020.1821591

IF: 1.7031

2020-01-01

Ironmaking & Steelmaking

Abstract:To solve the flatness problem in the production of hot wide strip temper mill with small-diameter work rolls, a finite element model of roll-strip coupling is established and the model accuracy is verified by comparison with the measured data. By calculating the contact pressure between rolls and the loaded roll gap profile, the effects of process parameters on the flatness adjusting are analysed. When adopting the positive bending force or increasing bending force to improve the edge wave, the strip is prone to the secondary defect of quarter buckle, especially for wide strips. To reduce the high-order deflection of the slender work roll and reduce the generation of quarter buckle, the temper mill should not use smaller rolling force. By optimising the back-up roll contour and the rolling force, the flatness adjusting performance of Handan Steel's hot temper mill was improved, and the flatness defective rate was reduced.
Tri-dimensional Elastic-Plastic Fem of Rolling Force During Strip Finishing Rolling Process

Huimin Yu,Xianming Zhao,Xingfeng Liu

2005-01-01

Abstract:A tri-dimensional elastic-plastic rolling model is developed using the software ANSYS/LS-DYNA.FEM. Calculations of rolling force for different temperature,strip thickness and depression are made by this model. Comparing rolling force values of the FEM calculation with theoretical calculation showed that the relative error between them was less than 11?%。
Numerical Simulation and Parameter Design of Strip Cold Rolling Process of 301L Stainless Steel in 20-Roll Mill

Junchen Li,Xutao Huang,Guocai Ma,Junwei Wang,Jixiang Pan,Qiang Ruan

DOI: https://doi.org/10.1007/s11663-020-01868-y

2020-05-29

Metallurgical and Materials Transactions B

Abstract:<p class="a-plus-plus">With the rapid development of rail vehicles, 301L strip has become the main material of the rail vehicles, and its flatness quality has got much attention. Meanwhile, 20-roll mill becomes the most important cold rolling equipment for 301L strip forming, because of its high precision and wide application. To study the flatness control theory of cold rolling 301L strip in 20-roll mill, a finite element model is established based on elastoplastic theory. The stress–strain field is used to characterize the strip flatness under different rolling parameters. After analysis, the results show that the front and back tension have the most obvious effects on strip flatness. The friction coefficient and rolling speed are beneficial to the control of the strip flatness when they increase within a certain range.</p>
ROLL WEAR ON FINISHING TRAIN OF 2050 CVC HOT STRIP MILL

连家创,黄传清,陈连生

DOI: https://doi.org/10.3321/j.issn:0449-749x.2002.03.008

2002-01-01

Abstract:Roll wear is a factor difficult to determine and there is no suitable theoretical model till now In this paper,the theoretical model of roll wear is established from the view of tribology,and the roll wear on finishing train of 2050 CVC hot strip mill has been measured The calculated results agree well with the measured,so the model for roll wear is of important significance for shape control

STUDY OF ROLLING FORCE MODEL ON HOT STRIP MILL

ANALYSIS AND MODIFICATION OF HYDRAULIC ROLLER BENDING FORCE CONTROL SYSTEM

Analysis of Rolling Force Model in Cold Rolling Mill

Analysis of Feasibility for Rolling Force Model Optimization of Hot Strip Mill of Jinan Iron & Steel Group Corporation

STUDY ON ROLL WEAR ON HOT STRIP ROLLING MILL

On the Optimization of a Rolling-Force Model for a Hot Strip Finishing Line

An analytical model of plate rolling force with a simple available velocity field and equal perimeter yield criterion

Rolling Process Analysis of Working Rollers of Cold Rolling Mill Based on ANSYS

Analytic Numerical Modeling for Thermal Mechanical Processing of Plate under Rolling

Research progress and intelligent trend of accurate modeling of rolling force in metal sheet

Study on Rolling Force during Asymmetric Rolling Process

Modelling of axial thrust force between rolls in strip mill

Research on the analytical model of rolling force for TiAl alloy pack rolling

Research on Mathematical Model of Loading Roll Gap for Strip Temper Mill

Simulation of the rolling process of 4-high hot steel strip continuous mills

Mathematical Models of Stable Roll Load of Double Stands Thin Gauge Strip Temper Mill

Shape and Crown Control Strategy for PC Mill

Numerical Analysis on Flatness Adjusting Performance of Hot Wide Strip Temper Mill with Small-Diameter Work Rolls

Tri-dimensional Elastic-Plastic Fem of Rolling Force During Strip Finishing Rolling Process

Numerical Simulation and Parameter Design of Strip Cold Rolling Process of 301L Stainless Steel in 20-Roll Mill

ROLL WEAR ON FINISHING TRAIN OF 2050 CVC HOT STRIP MILL