Abstract:<p>Polypropylene (PP) has been commonly used as packaging materials due to the favorable mechanical and optical properties related to its diverse and complex chain microstructure which can be better understood through effective fractionation. In this work, two commercial PP resins (A and B) with similar bimodal melting temperature distribution in the range of 100–160 °C but different ethylene content (9.1–12.3 mol%) are fractionated by preparative temperature rising elution fractionation (P-TREF) and relevant fractions are characterized by a variety of techniques such as high temperature-gel permeation chromatography (HT-GPC), differential scanning calorimetry (DSC), <sup>13</sup>C nuclear magnetic resonance (NMR) spectroscopy, Fourier transform-infrared (FT-IR) spectroscopy, and wide-angle X-ray diffraction (WAXD). The chain microstructures of the two resins used as food packaging film exhibit heterogeneity and some differences, which are mainly caused by broad and different distribution of ethylene comonomers. Resin B contains more ethylene units than resin A, and the ethylene units are incorporated into the PP chains in the forms of individual unit or very short segments, resulting in large amount of fractions with relatively low isotacticity and crystallinity that eluted at the temperature range of 35–90 °C. These fractions account for 84.07 wt% of resin B, whereas 59.66 wt% of resin A. The propylene sequences of different isotacticity and crystallinity generated by the insertion of ethylene comonomers in resin B are mainly responsible for its biomodal melting behavior. However, ethylene comonomers tend to insert into the PP chains of resin A in the forms of long polyethylene (PE) blocks and generate propylene−ethylene block copolymers with high crystallizability which can be eluted at high temperatures of 120–140 °C. These fractions constitute 3.16 wt% of resin A, but barely exist in resin B. Moreover, 35.83 wt% of resin A were eluted at 110 °C, whereas only 13.22 wt% of resin B can be eluted at this temperature. These fractions with high isotacticity and molecular weight eluted at high temperatures contribute to the higher flexural modulus of resin A. Both long ethylene blocks and propylene sequences of different lengths contribute to the biomodal melting peaks on the thermogram of resin A.</p>

Research and Application of Speciality Resin for Rotational Moulding Waterproof Packing Chests

Preparation of the ageing-resistant black amino molding plastics

Preparation of glass fiber reinforced phenolic injection molding materials and its properties

Structure and properties of HDPE speciality resins for hollow containers

Development of special resin HDPE 5500B for profiled bottles

Development of an Ultrasonic Method for the Quality Control of Polyethylene Tanks Manufactured Using Rotational Molding Technology

Development of technology of special material for hard PVC sections(Synthesis of special material for PVC modification by CPE)

DEVELOPMENT OF PLASTICS FOR ROTATIONAL MOLDING PROCESSING EQUIPMENT AND TECHNICS

Mechanical and gas barrier properties of polyamides 6/ organically modified montmorillonite/ maleic anhydride grafted polyolefin elastomer composites produced by rotational molding

Study on structure and properties of heat resistance polypropylene special resin

Model Simulation and Rheological Research on Crosslinking Behavior of Polyethylene Resin

The Study of Improving the Compatibility of the Blend of TVVM Resin and Polyester As a Non-Reactive Hot Melt Adhesive Used in OMD Technique

Comparison of chain microstructure between two propylene−ethylene copolymer resins with bimodal melting temperature distribution

Research on torsional laminated extrusion for improving the permeability and mechanical properties of HDPE/PA6 composite for type IV storage tank liners

Polymeric resin environmental stress crack resistance is improved

Practical Technology of Toughening Epoxy Resin (II): Modification Effects of Special Engineering Plastics on Epoxy Resin

The Characterization of Rheological Properties of Melt Grafting Polypropylene for Foaming

High-Impact Epoxy Resins with Superior Hydrophobicity Toughened by Epoxy Functionalized Poly(olefin-alt-maleimide) Derivatives

Rheology Study on Polypropylene Blends with in situ Core-Shell Dispersed Particles

Research on Crystallization Behavior and Mechanical Properties of Plasticized Polpypropylene

Toughening with Little Rigidity Loss and Mechanism for Modified Polypropylene by Polymer Particles with Core–shell Structure