Abstract:In the coal direct liquefaction process line distribution of finished oil tanks and semifinished oil tanks, corrosion of tank reservoir parts and the gas phase are important. To prove the corrosion‐influencing factors and corrosion processes of various parts of the storage tank, further research was carried out based on the previous research. As the process of corrosion of the tank wall is affected by the sulfur element in oil, the sulfur content in refined oil and semi‐refined oil was analyzed first. The results show that: the sulfur content is high for hydro‐upgrading feed oil and hydro‐stabilizing feed oil, but the sulfur content is low for thick condensed oil and diesel. The tank is mainly made of 16MnR and Q235‐b steel in the process plant. In this article, 16MnR and Q235‐b steel coupons are used for static coupon experiments and electrochemical experiments to determine the influencing factors and processes that affect the corrosion of the reservoir and the gas phase. The static coupon tests show that the corrosion rates are similar for 16MnR and Q235‐b steel coupons in the reservoir location and for the gas‐phase parts. And, the corrosion rates decrease with time. The corrosion rates of 16MnR and Q235‐b steel in hydro‐stabilizing feed oil are relatively high, and the corrosion rates of 16MnR and Q235‐b steel are relatively low, though the difference is not significant. The 16MnR corrosion rate is relatively high in the reservoir location compared to that of the gas phase. The corrosion rate of Q235‐b steel in the gas‐phase space is relatively higher than that of the reservoir location. Electrochemical tests show that the corrosion rates of 16MnR and Q235‐b steel in hydro‐stabilizing feed oil are higher than those in the other three oils. Finally, the effect of temperature on the corrosion rate was studied by the static coupon experiment. The results show that the corrosion rates of 16MnR steel and Q235‐b steel in the four kinds of oil products increase first and then decrease when the temperature changes from 70 to 110°C. The corrosion rate reaches the maximum when the temperature is 90°C. The research of this article can provide some technical support and help for the corrosion protection and safety design of oil tanks in the direct liquefaction process. © 2018 American Institute of Chemical Engineers Process Process Saf Prog 37:419–426, 2018

Study on Dew Point Corrosion and Ammonium Salt Depositing at Low Temperature System of Atmospheric and Vacuum Distillation Unit

Mitigation of the ammonium salts corrosion in overhead condensing system of crude tower

Corrosion in Atmospheric Distillation Unit Processing Russian Crude Oil and Protection

Effect of ammonium salt on corrosion of pipelines and components in a crude oil distillation column: Electrochemical and AIMD studies

Analysis on the corrosion characteristic and risk in atmospheric tower using Aspen plus software

Numerical and experimental study on corrosion mechanism of the water-oil two-phase flow in the atmospheric tower top system

Experimental study on the dew point corrosion behavior in atmospheric tower system

VAPOR PRESSURE MEASUREMNET OF LIQUID DESSICANTS AT LOW TEMPERATURES BY A NOVEL TECHNIQUE

Corrosion and protection for high temperature equipment in atmospheric-vacuum distillation units

Summarization of High-temperature Naphthenic Acid Corrosion and Its Control Technique on Pipeline

Crystallization Behavior of Ammonium Chloride in High-Pressure Heat Exchanger of Hydrotreating Unit

Failure analysis and prediction based on corrosion thinning behaviour of atmospheric tower top and volatilization line connection area

RESEARCH PROGRESS OF HIGH TEMPERATURE NAPHTHENIC ACID CORROSION RULES AND PREVENTION METHODS IN PETROCHEMICAL PLANTS

Low temperature simulation of ammonia refrigeration based on dissipative molecular dynamics

Understanding of ammonium salts under-deposit corrosion: Electrochemical and AIMD investigations

Failure analysis of ammonium chloride salt coagulation corrosion of U-tube heat exchanger in diesel hydrogenation unit

Aspen Plus Predict Water Dew Point and Ph Value of the Overhead Condensing System of Crude Atmospheric Distillation Unit

Study on the Superhydrophilic Modification and Enhanced Corrosion Resistance Method of Aluminum Alloy Distillation Desalination Tubes

Study of corrosion of oil tank parts and gas‐phase space in different tanks

Analysis of Multiphase Flow and Heat and Mass Transfer for Ammonium Chloride Crystallization of the High-Pressure Heat Exchanger in Hydrogenation Unit

Experimental study on crystal deposition mechanism of ammonium chloride particles on the surface of heat exchange tube