Abstract:A modified nano-calcium carbonate (R-CCR) was prepared by coating a layer of unsaturated hydroxylfatty acid on the surface of CCR powders using a solid state method; the latter were commercial nano-CaCO 3 modified with stearic acid. FTIR studies indicate that the modifier is combined on the surface of CaCO 3 . PP/EPDM/nano-CaCO 3 ternary composites were prepared by a melt-mixing method. SEM and TEM were utilized to examine the morphology of the composites. The tensile fractured surface of PP/EPDM/R-CCR showed a fibroid morphology and large-scale yield deformation. The impact fractured surface showed that the amount of cavities in the PP/EPDM/R-CCR system was increased, however their size diminished obviously. R-CCR particles were dispersed uniformly in the PP matrix, and their compatibility was distinctly improved as compared to CCR when the amount of R-CCR was 15 h −1 . The tensile strength remained nearly constant (reduced from 27.6 MPa to 27.5 MPa), while the impact strength increased from 9.6 kJ/m 2 to 15.4 kJ/m 2 as CCR was replaced by R-CCR. Meanwhile, the bending strength and bending modulus also increased correspondingly. Furthermore, the impact strength of PP/EPDM/R-CCR was maintained at a high level (15.4 kJ/m 2 ), which was more than the sum of that of PP/EPDM and PP/R-CCR (6.6 kJ/m 2 and 6.1 kJ/m 2 respectively). This indicates that the R-CCR and EPDM have a significant synergistic toughening effect on PP while maintaining the strength and modulus of virgin PP. Both the storage modulus G′ and loss modulus G″ of PP/EPDM and PP/EPDM/R-CCR composites increase with increasing frequency, but the values of G′ and G″ of the tertiary composite are relatively higher than those of the binary system. The loss factor and viscosity decrease with increasing frequency, but there is little difference between tertiary and binary composites. The apparent viscosity η of the tertiary system containing R-CCR is lower than that of the tertiary system containing CCR and virgin PP. The viscosity of the composites sig-nificantly decreases with increasing shear rate. The mea-sured mechanical properties of the composites indicate that replacing CCR with R-CCR for binary composites could simultaneously enhance the toughness and strength of PP.

EFFECTS OF CaCO3 PARTICLE SIZE AND SIZE DISTRIBUTION ON PROPERTY AND STRUCTURE OF PP

Enhancement on the properties of polypropylene using bamboo particles: Effect of particle sizes and loadings

The Influence of Calcium Carbonate on the Mechanical Properties and Phase Morphology of PA6/PP Blend

Effect of Oleic Acid-modified Nano-CaCO3 on the Crystallization Behavior and Mechanical Properties of Polypropylene

Study on the Properties and Structure of Polypropylene Modified with Nano-Sized CaCO_3

Mechanical and Thermal Properties of Polypropylene (PP) Composites Filled with CaCO3 and Shell Waste Derived Bio-Fillers

Study on the Preparation and Properties of Caco3/Polypropylene Composite Materials

Crystallization Behavior of PP in Composites with EPDM and a Surface Modified Nano-Calcium Carbonate

Modification Of Mechanical And Color Properties Of Polypropylene With Colored Nano-Sio2 Prepared From Diatomite

Effect of Unsaturated Hydroxyl-Fatty Acid Modified Nano-Caco3 on the Morphological and Rheological Behavior of PP

Study On Crystallization Behaviour Of Polypropylene Containing Nano-Calcium Carbonate And Organic Nucleating Agents

Modification of Poly(vinyl Chloride) with Nano-CaCO3 Coated with Poly(methyl Methacrylate)

Modification of mechanical and color properties of polypropylene with colored nano‐SiO<sub>2</sub> prepared from diatomite

Crystallization and Mechanical Properties of Polypropylene Filled with Sio2 Nanoparticles

Surface Modification of Shell Waste and Its Application in Polypropylene Composites

Effect of Surface Modification of CaCO_3 on Mechanical Properties of PP/CaCO_3 Composite

Effect of Light Intensity on Ultraviolet Irradiated Polypropylene and Its Compatibilization with CaCO3

Calcium Carbonate Particles Filled Homopolymer Polypropylene at Different Loading Levels: Mechanical Properties Characterization and Materials Failure Analysis

Effects of inorganic particles on the crystallization, mechanical properties and cellular structure of foamed PP composites in the IMD/MIM process

Electrical Resistivity, Crystallization and Mechanical Properties of Polypropylene/Multi-Walled Carbon Nanotube/Calcium Carbonate Composites Prepared by Melt Mixing

Effect of different nucleating agent on crystallization behavior and properties of batch bulk PP