Abstract:A modified nano-calcium carbonate (R-CCR) was prepared by coating a layer of unsaturated hydroxylfatty acid on the surface of CCR powders using a solid state method; the latter were commercial nano-CaCO 3 modified with stearic acid. FTIR studies indicate that the modifier is combined on the surface of CaCO 3 . PP/EPDM/nano-CaCO 3 ternary composites were prepared by a melt-mixing method. SEM and TEM were utilized to examine the morphology of the composites. The tensile fractured surface of PP/EPDM/R-CCR showed a fibroid morphology and large-scale yield deformation. The impact fractured surface showed that the amount of cavities in the PP/EPDM/R-CCR system was increased, however their size diminished obviously. R-CCR particles were dispersed uniformly in the PP matrix, and their compatibility was distinctly improved as compared to CCR when the amount of R-CCR was 15 h −1 . The tensile strength remained nearly constant (reduced from 27.6 MPa to 27.5 MPa), while the impact strength increased from 9.6 kJ/m 2 to 15.4 kJ/m 2 as CCR was replaced by R-CCR. Meanwhile, the bending strength and bending modulus also increased correspondingly. Furthermore, the impact strength of PP/EPDM/R-CCR was maintained at a high level (15.4 kJ/m 2 ), which was more than the sum of that of PP/EPDM and PP/R-CCR (6.6 kJ/m 2 and 6.1 kJ/m 2 respectively). This indicates that the R-CCR and EPDM have a significant synergistic toughening effect on PP while maintaining the strength and modulus of virgin PP. Both the storage modulus G′ and loss modulus G″ of PP/EPDM and PP/EPDM/R-CCR composites increase with increasing frequency, but the values of G′ and G″ of the tertiary composite are relatively higher than those of the binary system. The loss factor and viscosity decrease with increasing frequency, but there is little difference between tertiary and binary composites. The apparent viscosity η of the tertiary system containing R-CCR is lower than that of the tertiary system containing CCR and virgin PP. The viscosity of the composites sig-nificantly decreases with increasing shear rate. The mea-sured mechanical properties of the composites indicate that replacing CCR with R-CCR for binary composites could simultaneously enhance the toughness and strength of PP.

Crystallization Behavior of PP in Composites with EPDM and a Surface Modified Nano-Calcium Carbonate

Effect of Unsaturated Hydroxyl-Fatty Acid Modified Nano-Caco3 on the Morphological and Rheological Behavior of PP

Exploring the Effects of MXene on Nonisothermal Crystallization and Melting Behavior of Β-Nucleated Isotactic Polypropylene

Effect of Oleic Acid-modified Nano-CaCO3 on the Crystallization Behavior and Mechanical Properties of Polypropylene

Isothermal crystallization of polypropylene/surface modified silica nanocomposites

Study On Crystallization Behaviour Of Polypropylene Containing Nano-Calcium Carbonate And Organic Nucleating Agents

Mechanical and Thermal Properties of Polypropylene (PP) Composites Filled with CaCO3 and Shell Waste Derived Bio-Fillers

Study on the Properties and Structure of Polypropylene Modified with Nano-Sized CaCO_3

Effect of hydrophobic nano‐silica/β‐nucleating agents on the crystallization behavior and mechanical properties of polypropylene random copolymers

Crystallization and Mechanical Properties of Polypropylene Filled with Sio2 Nanoparticles

Crystallization, mechanical, and heat resistance performances of copolymer polypropylene modified by α nucleating agent

Crystallization kinetics and morphology of iso-PP/ethylene-propylene-b- copolymer/ ethylene-propylene-r-copolymer ternary blends

Crystallization‐correlated phase separation of polypropylene random copolymers

The effect of elastomeric nano-particles on the mechanical properties and crystallization behavior of polypropylene

Step crystal growth on β-nucleated polypropylene homocomposites governing the crystalline compositions

The Cellular Structure and Mechanical Properties of Polypropylene/Nano-CaCO3/Ethylene-propylene-diene-monomer Composites Prepared by an In-Mold-Decoration/Microcellular-Injection-Molding Process

The Crystallization Morphology and Conformational Changes of Polypropylene Random Copolymer Induced by a Novel β-Nucleating Agent

Crystallization Morphology and Behavior of Polypropylene Composites Containing Microencapsulated Flame Retardant

Modification of Polypropylene with Composite Nucleating Agents Containing 2,2-Methylene-bis-(4, 6-di-t-butylphenylene) Phosphate/Attapulgite/Silica Nano-particles

Non-isothermal crystallization behavior of polypropylene with nucleating agents and nano-calcium carbonate

Effect of Microstructure of Epr on Crystallization and Morphology of Pp/Epr Blends