Abstract:When a pump operates in part-load conditions, it is apt to form flow separations and even stall cells at the blade surfaces. In some conditions, stall cells may circumferentially propagate among the blade channels, known as rotating stall, which can affect the rotor system dynamic stability. Conventionally it is believed that the formation and circumferential propagation of stall cells is attributed to the nonuniformity of the flow state in front of the impeller inlet. In recent decades, many investigations indicate that the uneven flow field at the impeller outlet related to the asymmetric volute casing is also an important factor to induce rotating stalls. Thus the formation and propagation mechanism of rotating stalls is complex and has not been clearly understood so far. In addition, previous studies mainly focused on the rotating stalls in vaned diffusers, while it is more difficult to figure out rotating stalls in impellers for which little studies has been done. In this paper, numerical simulations are conducted for a three-blade centrifugal pump with a flow rate of 0.75Qd where Qd is the design flow rate. The SST-SAS model with a curvature correction is applied to predict the unsteady internal flows. The time-averaged pump head, efficiency and axial power agree well with the experimental results from a previous test. From the numerical results, a special rotating stall is detected in this condition. In order to verify the effect of the volute casing, a contrast simulation is also conducted without the volute casing domain. It shows that rotating stalls always occur whether there is a volute casing or not, but the distribution and motion of the stall cells are changed by the existence of the volute casing. It indicates that the nonuniform flow distribution at the impeller outlet is not an essential factor for the formation of rotating stall but accelerates the variation of stall cells. Based on the whole-flow-passage result, a stall cell in one blade channel disappears for about 2/15T (T is the duration of one revolution) when the downstream blade runs across the tongue, and the same phenomenon recurs in the upstream blade channel after 1/3T, which is unusual and worthy of investigation. The pressure fluctuations within the whole flow passage are intensified by the rotating stall more or less, especially at the middle region of pressure surface of blades, around the tongue and in the beginning of the discharge passage.

Principal Axis System's Critical Rotating Speed Calculation and Analysis of Dish Centrifuge

The Effect on Dish Centrifuge'dynamical Characteristic of the Unbalance Weight of Rotor

Analysis on Dynamic Characteristics and Design of Centrifuge

Distribution Law Analysis and Calculating Method for Windage Power in a Geotechnical Centrifuge

Analyse Rotor Dynamics of Agitating Shaft with the Finite Element Method

Dynamic Characteristics of Scraper-Discharge Material Centrifuge

Rotor Dynamic Characteristic Calculation of the Horizontal Helical-conveyer Centrifuge

An Experimental Study on Aerodynamic Characteristics of Hypergravity Centrifugal Facility

A Quasi-Dynamic Model for High-Speed Ball Spinning

Numerical Analysis of a New Type of Dishwasher Pump for Different Rotation Speeds of the Volute

Numerical simulation on effect of rotation speed on scoop power loss

Computing Critical Speeds for Multiple-stage Centrifugal Pumps with Dependent Support Properties

Vibration of Thick Rotating Cylindrical Shells

2D Numerical Study of the Feed Jet Flow Field in a Gas Centrifuge

Experimental and numerical analysis on the characteristics of flow field and precession moment in fluid momentum wheel with driven pump

NUMERICAL ANALYSIS OF THE TEMPE-RATURE DISTRIBUTION OF THE ROTOR SYSTEM IN THE CENTRIFUGE MADE OF TWO-LAYER MATERIALS

Aerodynamic Optimization Design of a Supergravity Centrifuge: A Low-Resistance Strategy

Nonlinear Dynamic Analysis of a Rigid Rotor Supported By a Spiral-Grooved Opposed-Hemisphere Gas Bearing

Numerical Theory and Method on the Modal Behavior of a Pump-Turbine Rotor System Considering Gyro-Effect and Added Mass Effect

Numerical Investigation on the Rotating Stall Characteristics in A Three-Blade Centrifugal Impeller

Influence of the Lateral Joint Stiffness Between the Shaft and Bearing on Centrifuge Stability