Abstract:Sn–Ni alloy matrix coatings co-deposited with TiO2 nanoparticles (Evonik P25) were produced utilizing direct (DC) and pulse electrodeposition (PC) from a tin–nickel chloride-fluoride electrolyte with a loading of TiO2 nanoparticles equal to 20 g/L. The structural and morphological characteristics of the resultant composite coatings were correlated with the compositional modifications that occurred within the alloy matrix and expressed via a) TiO2 co-deposition rate and b) composition of the matrix; this was due to the application of different current types (DC or PC electrodeposition), and different current density values. The results demonstrated that under DC electrodeposition, the current density exhibited a more significant impact on the composition of the alloy matrix than on the incorporation rate of the TiO2 nanoparticles. Additionally, PC electrodeposition favored the incorporation rate of TiO2 nanoparticles only when applying a low peak current density (Jp = 1 Adm−2). All of the composite coatings exhibited the characteristic cauliflower-like structure, and were characterized as nano-crystalline. The composites' surface roughness demonstrated a significant influence from the TiO2 incorporation rate. However, in terms of microhardness, higher co-deposition rates of embedded TiO2 nanoparticles within the alloy matrix were associated with decreased microhardness values. The best wear performance was achieved for the composite produced utilizing DC electrodeposition at J = 1 Adm−2, which also demonstrated the best photocatalytic behavior under UV irradiation. The corrosion study of the composite coatings revealed that they exhibit passivation, even at elevated anodic potentials.

Effects of Co2+ Content on Ti-coated Diamond-Ni-co Composite Electrodeposition

Electrodeposition and corrosion performance of Ni-Co alloys with different cobalt contents

Influence of the bath pH value on the microstructure and properties of a novel electrodeposited Ni-W-Ti3C2TX composite coating

Effect of Particle Concentration on the Microstructure and Properties of Electrodeposited Nickel–Diamond Composite Coatings

Effects of Direct and Pulse Plating on the Co-Deposition of Sn–Ni/TiO2 Composite Coatings

Effect of variations in Ni-W molar ratio on the microstructure, mechanical properties and tribology of electrodeposited Ni-W/diamond composite coatings

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

Comparative study on the properties and microscopic mechanism of Ti coating and W coating diamond-copper composites

Tailoring role of Al and Ti particles in the microstructure and property of electrodeposited Ni matrix nanocomposite coatings

Effect of cobalt content on electrodeposition and properties of Co–Ni alloy thin films

Effect of Pulse Electrodeposition Mode on Microstructures and Properties of Ni-TiN Composite Coatings

Effect of Nanodiamond Content in the Plating Solution on the Corrosion Resistance of Nickel–Nanodiamond Composite Coatings Prepared on Annealed 45 Carbon Steel

Influence of Ti3C2Tx Addition on the Corrosion Behaviour and Tribological Properties of Electrodeposited Ni-W-Ti3C2Tx Nanocomposite Coatings

Effect of Cobalt Content on the Properties of Nickel-Cobalt Alloy Coatings

Electrochemical Synthesis of Ni/TiO2 Composite Coatings from Deep Eutectic Solvent and Electrocatalytic Characteristics of Deposits

Introduction of heavy micro titanium carbide particles into Zn‐Ni coatings on steel during in‐situ brush electroplating

Technology for Ni-Al2O3 Composite Coating and Its Properties

Electrochemical Deposition and Nucleation/Growth Mechanism of Ni–Co–Y2O3 Multiple Coatings

Formation and Physicochemical Properties of Composite Electrochemical Coatings of Tin–Nickel Alloy with Silicon Dioxide Incapsulated by Nanosized Titanium Dioxide

Effect of Ti Doping on the Structure and Performance of LiNi0.75Co0.25O2

Effect of TiO 2 -Coating on Structure and Electrochemical Performance of LiCo 0.2 Ni 0.4 Mn 0.4 O 2