Abstract:Deformation and heat treatment are important means to strengthen aluminum alloys. However, the influence mechanism of pre-strain on aging precipitation kinetics and its effect on mechanical properties are still not clear. In this work, uniaxial isothermal tensile tests with different strains and artificial aging treatments for Al-Zn-Mg-Cu alloys have been carried out. Then, a model describing the precipitates kinetic behavior has been developed to investigate the effect of thermal pre-strain on subsequent aging precipitation kinetics and peak aging microhardness based on the microstructure characterization by TEM, SAXS and XRD tests. In addition, the role of dislocations on the aging precipitation kinetics is also explored. The experimental results show that the peak aging microhardness of the Al-Zn-Mg-Cu alloy reveals a tendency to decrease and increase and then the peak aging time firstly decreases and then keeps almost constant with the increase in the strain. The calculations demonstrate that the precipitate average size almost remains unchanged, while the precipitate volume fraction decreases and then increases with the increase in strain, which is consistent with the change in peak aging microhardness. It also indicates that dislocations can promote precipitate nucleation and growth, while the actual effect depends on the dislocation density, which is closely dependent on the pre-deformation condition, especially for the precipitate nucleation. In particular, when the dislocation density after thermal pre-deformation is not enough, it will slightly inhibit precipitate nucleation but promote precipitate growth, which could shorten the peak aging time, with the peak aging strength being guaranteed.

INFLUENCE OF VACANCY TYPE DEFECTS ON REVERSE TRANSFORMATION AND SHAPE MEMORY EFFECT IN A Cu-Al-Zn-Mn-Ni ALLOY

Stabilization of deformed stress-induced martensite and its effect on shape memory effect in an Fe-Mn-Si-Ni-Co alloy

Influence of Vacancy-Type Defects on the Stabilization and Shape Memory Effect of CuAlZnMnNi Martensite

Microstructure and martensitic transformation behavior of CuAlNb high temperature shape memory alloy

Deformation Dependence of Transformation Behavior of Ti-Ni-Nb Wide Hysteresis Shape Memory Alloy

Effects of cooling rate on martensitic transformation behavior and shape memory property for Ni-rich NiTiHf-Nb high-temperature shape memory alloy

Failure mechanism of reverse shape memory effect in a Cu-base alloy

Positron-Annihilation Study of Defects in Thermoelastic Martensite-Transformation of Cu-Base Shape Memory Alloy

Re-examination of martensitic stabilization in Cu-based shape memory alloys Part II. Key factors determining occurrence of martensitic stabilization in Cu-based alloys

Influence of Deformation Temperature on Shape Memory Effect of Fe–Mn–Si–Ni–Cr Alloy

Reverse Transformation Crystallography of Deformed Martensite in Ni-Mn-Ga Shape Memory Alloys

Effect of Heating/Cooling Rate on the Transformation Temperatures in Tinicu Shape Memory Alloys

The Mechanisms of Two Way-Shape Memory Effect in A Cu-Zn-Al Alloy

High Undercooling Effect on Magnetic Shape Memory Co–Ni–Ga Alloys

Experimental and Simulation Study for the Influence of Thermal Pre-Deformation on Subsequent Aging Precipitation Kinetics of Al-Zn-Mg-Cu Alloy

A Study of Structure of Metastable Cu–Zn Alloys with Shape Memory Effect

Reverse transformation characteristics of thermally induced ε(hcp) martensite in an Fe-Mn-Si based alloy

Effect of pre-deformation on martensitic transformation behavior and the microstructure of a Ni–Mn–Ga alloy

Effect of Ni alloying on vacancy behavior and damping capacity in martensitic ductile Cu–Al–Mn alloys

Effect of Stoichiometry on Shape Memory Properties of Ti-Ni-Hf-Cu-Nb Shape Memory Alloys Manufactured by Suspended Droplet Alloying

Strain Recovery Characteristics And Reverse Transformation Of Deformed Martensite In A Ni-Ti-Nb Wide Hysteresis Shape Memory Alloy