Abstract:BACKGROUND Zirconia is one of the most widely used ceramic materials for transplanting and treating caries. This study aimed to synthesize zirconium oxide (ZrO₂) nanotubes and evaluated their characteristics. MATERIAL AND METHODS Zr film was prepared using an ion plating method. Nanoarray film was constructed with anodizing. Photocatalytic properties of nnanotubes were assessed by evaluating decolorization of methyl orange. Elemental analysis and structural morphology for coatings were evaluated using x-ray analysis and scanning electron microscopy (SEM). Dimensions for layers were measured with SEM imaging. X-ray diffraction (XRD) was measured using Empyrean x-ray diffractometry. RESULTS There were irregular cavities on the surface of ZrO₂ nanotubes undergoing anodizing of 30V. Anodizing voltage of 45 V (with regular nano-pore arrays and smooth nanotube walls) and anodic oxidation duration of 60 min (ZrO₂ nanotubes clearly formed atop ZrO₂-coated substrate surface) were the optimal condition for ZrO₂ nanotube formation. TEM illustrated tube length of ZrO₂ nanotubes was approximately 2.01 μm. Nanotube diameter was 51.06 nm, and wall thickness was 13 to 14 nm. Annealed nanotubes showed an obvious crystal diffraction pattern. TEM diffraction ring showed nanotube array without obvious transistor structure before annealing, but with good crystallinity post-annealing. Increased annealing temperatures result in enhanced intensity for the monoclinic phase (400-800°C). After annealing at 600°C, the decolorization effect of ZrO₂ nanotubes on methyl orange was better than that post-annealing at 400 and 800°C. ZrO₂ nanotubes demonstrated higher microshear bond strength. CONCLUSIONS Zirconium nanotubes were successfully synthesized and demonstrated good structural characteristics, which can be applied to transplanting and treating caries.

Preparation and Structural Properties of Zirconia Nanotubules

Fabrication and characterization of highly ordered zirconia nanowire arrays by sol–gel template method

Preparation and characterization of yttria-stabilized zirconia nanotubes

Freestanding ZrO2 Nanotube Membranes Made by Anodic Oxidation and Effect of Heat Treatment on Their Morphology and Crystalline Structure

Synthesis and Characterization of Zirconia Nanorods

Preparation of a Novel Transplant Material, Zirconium Oxide (ZrO₂) Nanotubes, and Characterizations Research

Highly Ordered Zinc Oxide Nanotubules Synthesized Within the Anodic Aluminum Oxide Template

Hydrothermal Synthesis and Characterization of Zirconia Nanocrystallites

Fabrication of ZnO/Al2O3 core–shell nanostructures and crystalline Al2O3 nanotube

Preparation and Microstructure of Nanometer Tetragonal Polycrystal Zirconia Powder at Low Temperature Condition

Influencing factors and growth mechanism in hydrothermal preparation of ZrO2 nanotubes

Preparation and characterization of zirconia membrane

Synthesis of zirconia nanoparticles on carbon nanotubes and their potential for enhancing the fracture toughness of alumina ceramics

Tunable Structure of Zirconia Nanoparticles by Biopolymer Gelation: Design, Synthesis and Characterization

Monoclinic zirconium oxide nanostructures synthesized by a hydrothermal route

Preparation and characterization of yttria stabilized zirconia nanoarrays

Fabrication Parameter-Dependent Morphologies of Self-Organized Zro2 Nanotubes During Anodization

An Array of Concentric Composite Nanostructures of Zirconia Nanotubules/Cobalt Nanowires: Preparation and Magnetic Properties

Preparation and Characterization of Alumina-Zirconia Nanoparticles

Hierarchically Ordered Networks Comprising Crystalline ZrO2 Tubes Through Sol–gel Mineralization of Eggshell Membranes

Preparation and Structure Analysis of Titanium Oxide Nanotubes