Abstract:In this paper, the Ag–Au–Al alloy is prepared, its effect on the microstructure and properties is observed by changing the content of aluminum. Ternary alloys are tested for hardness and resistivity. The results show that Ag‐15wt.%Au‐14wt.%Al alloy has the highest hardness and the lowest resistivity. The authors also used first‐principles calculations. The calculation results are in good agreement with the experiment. In this paper, the silver–gold–aluminum alloy is prepared, and its effect on the microstructure and properties is observed by changing the content of aluminum. SEM observes the surface morphology, EDS (Energy Dispersive Spectrometer) detects the related tissue composition, and XRD (X‐ray Diffraction) verifies the composition. Ternary alloys are tested for hardness and resistivity. The results show that Ag‐15wt.%Au‐14wt.%Al alloy has the highest hardness. The resistivity test shows that Ag‐15wt.%Au‐18wt.%Al alloy has the lowest resistivity. The change in Al content improves the alloy's mechanical properties and electrical conductivity. This paper uses the first‐principles calculation based on density functional theory to prove the structural stability from the atomic point of view. The mechanical properties, electrical properties, and thermodynamic properties of Ag‐Au‐Al ternary alloys are systematically studied, including elastic constants, elastic modulus (including bulk modulus B, shear modulus G, Young's modulus E, Poisson's ratio ν), Vickers hardness. The mechanical properties of the single crystal are evaluated by Cauchy pressure, Pugh criterion, shear anisotropy factor, and directional Young's modulus, and the Debye temperature is calculated. The calculation results are in good agreement with the experiment. The research in this paper provides a new idea for studying the properties of new bonding wires.

Solubility after Mechanical Alloying for Al-Pb Immiscible Alloy System

The Effect of A Small Amount of Tungsten on the Microstructure of Mechanically Alloyed Ag37cu63

Embedded Atom Potential Calculation of the Al–Pb Immiscible Alloy System

Strengthening Effect of Ag Precipitates in Cu–Ag Alloys: A Quantitative Approach

Phase Structure Analysis of AgCd and AgSn Alloy Powders

Study on Phase Transformation and Thermodynamic and Kinetic of Al-Pb Powder During Mechanical Alloying

Metastable Structures of Immiscible System Induced by Mechanical Alloying

Mechanical alloying of immiscible Pb-Al binary system by high energy ball milling

Mechanical Alloying of Immiscible Elements: Ag-Fe Contrasted with Cu-Fe

Study on Structures Stability, Mechanical Properties, and Electronic Properties of Alloy Ag–Au–Al: First‐Principles Calculations and Experiments

Formation of nanocrystalline and amorphous phase of Al-Pb-Si-Sn-Cu powder during mechanical alloying

Structural Stability and Homogeneity of the Nonequilibrium Co–Ag Alloys

Solid-State Alloying in Binary Systems with a Positive Heat of Mixing

Microstructure and Morphology of Al-Pb Bearing Alloy Synthesized by Mechanical Alloying and Hot Extrusion

Investigation of Microstructure and Thermo-stability of Ag-cu-sn Filler Metal Powders Prepared by Mechanical Alloying

Research on homogeneous nucleation and microstructure evolution of aluminium alloy melt

Alloying in a System with Positive Heat of Mixing: MD Simulations of Ag-Cu

Mechanical Alloying of the Immiscible Cu-60wt%Cr Alloy: Phase Transitions, Microstructure, and Thermodynamic Characteristics

Microstructure and Wear Properties of Al–Pb–Cu Alloys Prepared by Mechanical Alloying

Atomic structures of nonequilibrium alloys in an immiscible Co–Ag system

Fcc Solid Solution Alloy Films Formed in Immiscible Fe–Ag System and Their Mechanical Behaviors