Abstract:WC-Co cemented carbides are widely used in the fields of military, aerospace, mining and cutting industry etc. In this paper, a new two-step method for the preparation of WC-Co cemented carbides was proposed. First, the mixture of yellow tungsten trioxide (WO3) and cobaltic oxide (Co2O3) were reduced by carbon black to remove all the oxygen. Then, the carbothermic reduction products were precisely mixed with an appropriate amount of carbon black to directly prepare WC-Co cemented carbides. The effects of C/WO3 ratio on the phase composition, morphological evolution, particle size and mechanical properties of products are investigated. The experimental results revealed that when the C/WO3 molar ratio was above 2.7, all oxygen in the raw material mixture were removed by carbon black and a mixture of W2C and η-phase were obtained after the first step of carbothermic reduction at 1150 °C for 2 h; then, the mixture of carbothermic reduction product and an appropriate content of carbon black was compacted, and the green compact was first carbonized at 1200 °C for 2 h and then sintered at 1450 °C for 4 h to prepare cemented carbides. With the increase of C/WO3 ratio at the first stage, the content of η-phase with a low melting point increased, which resulted in the large grain size of WC in the finally prepared cemented carbide. Compared with the traditional method of preparing cemented carbides, the cemented carbides prepared by the current method showed a higher hardness and toughness. Furthermore, the addition of a proper content of the VC in the second stage can significantly inhibit the grain growth of WC and further increase the hardness of cemented carbides.

Surface Modification of Wc-Based Cemented Carbide by One-Pot Non-Vapor Deposition Method Derived Al2o3 Coatings

Microstructure and wear resistance of bimodal cemented carbide coating prepared by direct laser powder deposition

Coprecipitation of co and La 2 O 3 coprecipitation on WC for tailoring the grain distribution and boundary of high-performance coarse-grained WC-10Co cemented carbide

Promising WC-30WB-10Co Cemented Carbide Coating with Improved Density and Hardness Deposited by High Velocity Oxy-Fuel Spraying: Microstructure and Mechanical Properties

A short and facile process to synthesize WC-Co cemented carbides

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

WC-18wt.% Co with simultaneous improvements in hardness and toughness derived from nanocrystalline powder

Study on surface properties of coated WC-Co alloy based on laser reduction process

Reprint of “A Study of CVD Diamond Deposition on Cemented Carbide Ball-End Milling Tools with High Cobalt Content Using Amorphous Ceramic Interlayers”

Enhanced Coarse-Grained WC-Co(Ce) Cemented Carbide Prepared through Co-Precipitation

Performance Enhancement of Ultra-Coarse Cemented Carbide by Boride Additives

Synthesis of Y2O3-doped WC-Co powders by wet chemical method and its effect on the properties of WC-Co cemented carbide alloy

On the Enhanced Wear Resistance of Ultra-Coarse WC-Co Cemented Carbides by WCoB Addition

High-performance WC-AlCoCrFeNi 2.1 cemented carbides fabricated by resistance seam additive manufacturing

A facile route to prepare ODS WC Co cemented carbides

WC-Co Cemented Carbides Modified by Nano-sized Rare Earth Oxides

Improvement Of Adhesive Strength And Surface Roughness Of Diamond Films On Co-Cemented Tungsten Carbide Tools

Microstructure and mechanical properties of WC–Co-based cemented carbide with bimodal WC grain size distribution

A New Strategy to Efficiently Fabricate Tungsten Carbide Coating on Tungsten: Two-step Interstitial Carburization

One-step synthesis of ultrafine WC–10Co hardmetals with VC/V 2 O 5 addition by plasma assisted milling

Surface Modification of Cemented Carbide Using Plasma Nitriding and Metal Ion Implantation