Abstract:Ceramic cutting tool materials possess specific advantages, including high hardness, excellent wear resistance, and high chemical stability, making them unparalleled in the machining of difficult-to-process materials compared to traditional cutting tools. The mechanical performance of these materials is primarily determined by their microstructure. Therefore, it is necessary to simulate and optimize the microstructure of ceramic cutting tool materials to provide theoretical guidance for further enhancing their fracture toughness. In this paper, a simulation model based on sintering densification theory was proposed, coupling crystal plasticity with a three-dimensional cellular automaton, to investigate the impact of nanoparticle content, sintering temperature , sintering pressure, and holding time on grain growth in composite ceramic materials using spark plasma sintering (SPS). Furthermore, an evolution model for grain growth of TiB 2 -TiC-SiC nanocomposite ceramic materials in cutting tools is established, and the optimal sintering process parameters are obtained. Finally, SPS experiments were conducted. Under the conditions of a sintering temperature of 1600 °C, holding time of 7 min, and sintering pressure of 40 MPa, optimal mechanical performance composite ceramic cutting tool materials were prepared. The experimental results, including a hardness of 25.6 GPa, fracture toughness of 7.1 MPa·m 1/2 , and flexural strength of 628.2 MPa, were consistent with the simulation outcomes. This indicates that the designed simulation model for nanocomposite ceramic grain growth reliably reflects the physical process of grain growth in the material and provides valuable guidance for further understanding the mechanisms underlying grain growth.

Finite Element Simulation of Vickers Micro-Indentation Test of Micro-Nano-Composite Ceramic Tool Materials Based on Microstructure Model

Prediction of macroscopic effective elastic modulus of micro-nano-composite ceramic tool materials based on microstructure model

Theoretical Hardness Analysis and Experimental Verification for Composite Ceramic Tool Materials

Numerical modeling of Vickers indentation on polycrystalline alumina

3D Simulation of the Micro Indentation Process and Relative Problems Research

Finite Element Analysis of the Nanomechanics of Hard Coatings on a Soft Polymer Substrate by a Spherical Indenter

Mechanisms and FEM Simulation of Chip Formation in Orthogonal Cutting In-Situ TiB2/7050Al MMC

Optimization of sintering parameters for fabrication of Al2O3/TiN/TiC micro-nano-composite ceramic tool material based on microstructure evolution simulation

Microscale Simulation on Mechanical Properties of Al/Ptfe Composite Based on Real Microstructures

Finite Element and Experimental Analysis of Vickers Indentation Testing on Al2O3 with Diamond-Like Carbon Coating

Finite Element Modeling of the Indentation and Scratch Response of Epoxy/Silica Nanocomposites.

Numerical Comparison Between Berkovich and Conical Nano-Indentations: Mechanical Behaviour and Micro-Texture Evolution

Microstructure-Based Computer Simulation And Mechanical Modeling Of Particle-Reinforced Composites

Three-dimensional modeling of grain structure growth within ceramic tool material

Microstructure Reconstruction and Numerical Simulation of Deformation in Particle-Reinforced Composites

Experimental and FEM Study of Cutting Mechanism and Damage Behavior of Ceramic Particles in Orthogonal Cutting SiCp/Al Composites

Finite Element Simulation of Surface Micro-Indentation Behavior of Yttria Stabilized Zirconia Thermal Barrier Coatings with Microstructural Characteristic of Columnar Grains and Sub-Grains Based on a Nonlinear Contact Model

Numerical modeling and failure evolution of microstructure-based in-situ TiB2 and TiC+TiB2 reinforced Cu matrix composites

Real Microstructure-Based Simulation of Thermal Residual Stresses in Cemented Carbides and the Related Strengthening and Toughening Consideration

Microstructure-based Simulation of Plastic Deformation Behavior of SiC Particle Reinforced Al Matrix Composites

Hardness and Yield Strength of Micro-Nano TaC-Fe Composite Layer Characterized Through Nano-Indentation, Finite Element Simulation and Dimensional Analysis