Abstract:In this paper, we tested the mechanical properties at room and high temperatures, and compared the cutting performance of three ceramic tool materials with different components added sequentially. By analyzing and comparing, the influence of material components on the changes in material mechanical properties and cutting performance is obtained, and the guidance for material system design is proposed. Three kinds of Si3N4‐based ceramic tools (single‐phase Si3N4, Si3N4/(W,Ti)C, and Si3N4/(W,Ti)C/Ni) were fabricated by microwave sintering. The phase composition, toughening mechanism, mechanical properties at room and high temperatures (800°C), and cutting performance of Si3N4‐based ceramic tool materials with different additives were investigated. The results showed that the addition of (W,Ti)C and Ni had a significant effect on improving the mechanical properties at room temperature, although it reduced the phase transition conversion rate of Si3N4. Si3N4/(W,Ti)C tools had good high‐temperature stability, while Si3N4/(W,Ti)C/Ni tools had a decrease of about 31.6% in high‐temperature hardness and a decrease of 13.7% in high‐temperature flexure strength. Under the premise of ensuring a certain level of fracture toughness, high‐temperature hardness is the main influencing factor on the cutting life of cutting tools. The Si3N4/(W,Ti)C tools exhibit superior cutting performance whose cutting life reaches to 50.67 min which was 1.37–3.27 times longer than the other two ceramic cutting tools at the same cutting parameters when continuous dry cutting T10A. In addition, high‐temperature flexure strength limits the choice of cutting speed, and lower high‐temperature flexure strength can lead to rapid tool failure.

Effect of metal phases on microstructure and mechanical properties of Si3N4-based ceramic tool materials by microwave sintering

Preparation and characterization of Si3N4-based composite ceramic tool materials by microwave sintering

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Microstructure and Mechanical Properties of Spark Plasma Sintered Si3N4/WC Ceramic Tools

Effects of Ti(C, N) addition on the microstructure and mechanical properties of spark plasma sintered Si3N4/Ti(C, N) ceramic tool material

Enhanced Performance in Si3N4 Ceramics Cutting Tool Materials by Tailoring of Phase Composition and Hot-Pressing Temperature

Synergistic Reinforcement of Si3N4 Based Ceramics Fabricated via Multiphase Strengthening under Low Temperature and Short Holding Time

Effects of sintering additives on mechanical properties and microstructure of Si3N4 ceramics by microwave sintering

Microstructure And Mechanical Properties Of Sic Ceramic Toughened With Tin Nanoparticles

The influence of components on the high‐temperature performance and cutting performance of Si3N4‐based ceramic tools

Microwave Sintering of Ti(C, N)-based Cermet Cutting Tool Material

Preparation and mechanical properties of SiCw-reinforced WC-10Ni3Al cemented carbide by microwave sintering

Effect of Initial Phase Composition on the Phase Composition, Microstructure, and Mechanical Properties of Si3N4 Ceramics

Optimization of sintering parameters for fabrication of Al2O3/TiN/TiC micro-nano-composite ceramic tool material based on microstructure evolution simulation

Dynamic fatigue behavior of Si3N4-based ceramic tool materials at ambient and high temperatures

Preparation and characterization of medium entropy alloy CrCoNi toughened SiC ceramics

Fine Grained Al2O3/SiC Composite Ceramic Tool Material Prepared by Two-Step Microwave Sintering

Study on the mechanical properties and microstructure of Al2O3/nano-SiC multiphase ceramics

Microwave Sintering of Si3N4 Ceramics

Study on Microstructures of Micron Si 3 N 4 Composite Ceramic with Addition of Nano SiC and SiC Whisker

Effect of Si3N4 Additive on Microstructure and Mechanical Properties of Ti(C,N)-Based Cermet Cutting Tools