Abstract:C/C materials represent as materials with specific performance, therefore they are applied in various industries. It is essential to figure out the paths to predict, to provide and to enhance their properties to obtain high performance products. It is well known that strong matrix/reinforcer adhesion provides better strength utilization and therefore better properties for the majority of composite materials of all types (Heim in Compos Part B Eng 54:365–370, 2013), (Hancock and Cuthbertson in J Mater Sci 5:762–768, 1970), (Yang et al. in Polymers 13:2764, 2021). However some researchers note that strong adhesion in the materials that are exposed to high temperatures leads to cracking and significant properties degradation (Vignoles et al. in The Control of interphases in carbon and ceramic matrix composites, Wiley, Hoboken, 2012), (Zhang et al. in Compos Struct 340, 2024). In this work, the effect of the pyrocarbon layer applied on the surface of carbon fibers used for reinforcement of formaldehyde novolac resin based carbon/carbon (C/C) material prepregs was investigated. For the first time we used this effect to prove that lower matrix/reinforcer adhesion in C/C materials prepregs leads to better material behavior during pyrolysis, which results in higher mechanical properties of the pyrolised samples in comparison with the samples demonstrating stronger matrix/reinforcer adhesion. The prepregs were thermally treated at various temperatures, the physical and mechanical performance evolution of the prepregs at different carbonization stages were analyzed. Comparative study of the features of the prepregs with pyrocarbon coated and uncoated carbon fiber as a reinforcement were carried out. The damping effect of the pyrocarbon on the fiber surface were advertised, allowing to mitigate the carbonization-caused effects. The prepregs reinforced with pyrocarbon-modified carbon fibers demonstrated lower cracking performance and higher mechanical performance comparing with the uncoated fiber reinforced prepregs.

Influence of a Pre-Coated Pyrocarbon Layer on the Microstructure and Mechanical Properties of ZrC-doped C/C Composites

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

Effects of HfC/PyC Core-Shell Structure Nanowires on the Microstructure and Mechanical Properties of Hf1-xZrxC Coating

Study on toughening mechanisms of pyrolytic carbon interface layer in Cf/ZrB2-SiC composites using in-situ tensile experimental and numerical methods

Damage Mechanism Analysis to the Carbon Fiber and Fiber-Ceramic Interface Tailoring of Cf/ZrC-SiC Using PyC Coating

Using PyC Coated Short Chopped Carbon Fiber to Tackle the Dilemma Between Toughness and Strength of ZrC-SiC

Microstructure Analysis of Zirconium Carbide Layer on Pyrocarbon-Coated Particles Prepared by Zirconium Chloride Vapor Method

Correlation of C/C preform density and microstructure and mechanical properties of C/C-ZrC-based ultra-high-temperature ceramic matrix composites

PyC interphase growth mechanism and control models of C/SiC composites

Microstructure and ablation performance of HfC/PyC core-shell structure nanowire-reinforced Hf1-xZrxC coating

Influences of deposition temperature, gas flow rate and ZrC content on the microstructure and anti-ablation performance of CVD-HfC-ZrC coating

Effect of carbon matrix on mechanical and tribological properties of Cf/Cu/C composites

Effect of preset interfacial ZrB 2 particles on the microstructure and properties of C/C-AlSi composites

Interfacial microstructure and mechanical properties of Cf/AZ91D composites with TiO2 and PyC fiber coatings

Effect of pyrolytic carbon interphase on mechanical properties of mini T800-C/SiC composites

Microstructure and Ablation Behavior of W/ZrC/SiC Coating on C/C Composites Prepared by Reactive Melt Infiltration and Atmospheric Plasma Spraying

Architectural Engineering Inspired Method of Preparing C-f/ZrC-SiC with Graceful Mechanical Responses

Effects of multilayer hydrothermal carbon interphases on mechanical properties and thermal shock resistance of CF/ZrB 2 -SiCBN

Texture control of pyrolytic carbon coatings and effects of coating thickness on the tensile properties of SiC fibers

Reinforcement of C/C materials prepregs with pyrocarbon coated carbon fiber as the way to improve the prepregs properties after pyrolysis