Abstract:Diffusion and polymerization behaviour of styrene (St) in commercially. available high density polyethylene (HDPE) pellets were studied and HDPE/PS nanoblend pellets were synthesized. Both the diffusion and polymerization steps were carried out in water medium. At 70 - 90 degrees C, diffusion behaviour of St towards HDPE pellets showed features of Fickian Diffusion. The saturation values of diffused St were different at different diffusion temperatures, and higher diffusion temperature meant higher saturation value, higher diffusion rate and shorter time to reach the saturation value. The amount of the initiator BPO was important in view of PS content in the pellets. With 0. 5 wt% - 1 wt% BPO, PS content was 11 wt% when diffusion and polymerization were carried out at 90 degrees C, while the PS content increased to about 16 wt% when excess amount of BPO (5 wt%) was used. The diametrical distribution of PS was investigated by Micro Fourier Transform Infrared Spectroscopy, showing that PS appeared throughout the HDPE pellets. PS distributions along the diameters of the pellets showed similar "M" shape curves for HDPE/PS pellets synthesized with different amounts of BPO. The peaks of the curves appeared at 200 mu m area to the surface and were related to crystalline structure of HDPE pellets. The phase morphology of PS in the blend pellets were characterized by field emission scanning electron microscopy. Typical sea. island morphology was revealed with an average particle size of less than 100 nm. The HDPE/PS blend pellets were melt. processed into cylindrical bars. PS phases in the extrusion bars of the blend pellets synthesized with 0. 5 wt% BPO showed Ci Rice morphology, reflecting that PS particles were aggregating instead of coalescing during processing, and particle sizes were from tens of nm to 200 nm. The disperse PS phase and HDPE matrix had good interaction and the HDPE/PS bars did not break with elongation of 600% and showed higher tensile stress than pure HDPE bars, which meant that 0. 5 wt% BPO was fairly good condition for preparing HDPE/PS nanoblends or other modified HDPE materials.

Control of Surface Morphology of Polypropylene/polystyrene Blend Pellets Prepared by Diffusion and Subsequent Polymerization of Styrene in Isotactic Polypropylene Pellets

Compatibilizing Efficiency of Copolymer Precursors for Immiscible Polymer Blends

Polypropylene/Polystyrene Blends Prepared by Diffusion and Subsequent Polymerization in Polypropylene Pellets after Injection Molding

Diffusion and Polymerization Behavior of Styrene in High Density Polyethylene Pellets

Control of Diffusion/Barrier Effects of Polymer-Coated Particles and the Strengthening of Ethylene Polymerization Reactor

Reducing the Surface Stickiness of Multiphase Polypropylene Particles: an Environmentally Friendly and Scalable Method

Preparation of Isotactic Polypropylene/Polystyrene Blends by Diffusion and Subsequent Polymerization of Styrene in Isotactic Polypropylene Pellets

Diffusion and Polymerization Behavior of Styrene in Polypropylene Pellets of Different Aggregation State

Preparation of POE/PS Blends with Fine Particle Sizes by Diffusion and Subsequent Polymerization of Styrene in POE Pellets

Polymerization Kinetics of Styrene in Isotactic Polypropylene Pellets and Evolution of Phase Morphology During Polymerization

Morphology stabilization of the polypropylene/polystyrene nanoblends prepared by diffusion and polymerization of styrene in isotactic polypropylene pellets during melt mixing by the incorporation of divinylbenzene

Preparation of Polyamide 6/polystyrene Quasi‐nanoblends by Diffusion and Subsequent Polymerization of Styrene in Water‐sorbed Polyamide 6 Pellets

Diffusion and Polymerization Behavior of Styrene in Polyethylene Pellets of Different Molecular Structures

Morphology, thermal behavior, rheological, and mechanical properties of polypropylene/polystyrene blends based on elongation flow

Preparation of Polypropylene/Poly（styrene-co-（butyl Methacrylate）） Nanoblends by Diffusion and Subsequent Copolymerization of Monomers in Isotactic Polypropylene Pellets

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

In Situ Compatibilization of Polypropylene and Polystyrene-Grafted Nano-Sized TiO2 in the Presence of Friedel–Crafts Catalyst

Morphology and Mechanical Properties of Polyamide 6/Polystyrene Blends Prepared by Diffusion and Subsequent Polymerization of Styrene in Polyamide 6 Pellets

Influences of Compatibilization and Compounding Process on Electrical Conduction and Thermal Stabilities of Carbon Black‐filled Immiscible Polypropylene/polystyrene Blends

Improvement of PET surface hydrophilicity and roughness through blending

Hypercrosslinked Polystyrene Microspheres with Bimodal Pore Size Distribution and Controllable Macroporosity