Abstract:Single-crystal nickel-based CMSX-6 superalloy rods were directionally solidified at a constant withdrawal rate by employing a novel directional solidification process the downward directional solidification process and the Bridgman process. For the rods cast using both processes, the local cooling rates were measured at the 5.5 cm and 12.5 cm locations between the solidification front and the chill end. With an increasing distance from the chill, the cooling rate varied from 1.21 to 1.08 K/s giving a change in the rate of 10.74% in the novel process. In contrast to this, the cooling rates in the Bridgman process varied from 0.15 to 0.08 K/s giving a change in the rate of 46.67%. The microstructural evolution was comparatively investigated for the two processes as a function of the cooling rates. In comparison to the Bridgman process, refined gamma dendrite structures, smaller size of gamma/gamma' eutectic island, refined gamma' precipitates in the dendritic core and a smaller average size of microporosities were observed in both locations of the rods cast by using the novel process. In addition to this, the variations of the primary and secondary dendrite arm spacings, the size of gamma/gamma' eutectic island, and the size of gamma' precipitates in the dendrite core were smaller than those in the Bridgman process with increasing the distance from 5.5 cm to 12.5 cm. This indicates that the downward directional solidification process can cast a rod possessing more homogeneous microstructures. Moreover in comparison to the Bridgman process, the majority of the micropores have smaller diameters and both the variation in the maximum size of microporosity as well as the average diameter of these micropores located between positions near to the chill end and the distant end were smaller in the rods cast by using the novel process; the opposite is found in the Bridgman process. (C) 2014 Elsevier B.V. All rights reserved.

Comparative Investigation of the Downward and Upward Directionally Solidified Single-Crystal Blades of Superalloy CMSX-4

Influence of the Size Effect on the Microstructures of the DWDS- and Bridgman-Solidified Single-Crystal CMSX-4 Superalloy

Comparative Study of the Segregation Behavior and Crystallographic Orientation in a Nickel-Based Single-Crystal Superalloy

A High Thermal Gradient Directional Solidification Method for Growing Superalloy Single Crystals

Effect of Local Cooling Rates on the Microstructures of Single Crystal CMSX-6 Superalloy: A Comparative Assessment of the Bridgman and the Downward Directional Solidification Processes

Effect of Directional Solidification Methods on Solid Solution Window in Ni-based Single-Crystal Superalloy

Effect of Solidification Parameters on the Microstructures of Superalloy CMSX-6 Formed During the Downward Directional Solidification Process

Investigation of Segregation and Density Profiles in the Mushy Zone of CMSX-4 Superalloys Solidified During Downward and Upward Directional Solidification Processes

Innovations in Casting Techniques for Single Crystal Turbine Blades of Superalloys

Microstructural Investigations of Ni-Based Superalloys by Directional Solidification Quenching Technique

Directional Solidification Behavior of CMSX-6 Superalloy

Improving Microstructural Homogeneity of Investment‐Cast Single‐Crystalline Ni‐Base Superalloys by Employing Fluidized Carbon Bed Cooling

Processing, Microstructures and Mechanical Properties of a Ni-Based Single Crystal Superalloy

Modeling of Directional Solidification of Columnar Grain Structure in CMSX-4 Nickel-Based Superalloy Castings

Substrate stimulating technique for Ni-based single crystal superalloy preparation during direction solidification

Effect of Directional Solidification Variables on the Microstructures of Single-Crystal Turbine Blades of Nickel-Based Superalloy

Solidification and microsegregation behaviors of nickel-base single crystal superalloy solidified at medium cooling rate

Orientation Control for Nickel-Based Single Crystal Superalloys: Grain Selection Method Assisted by Directional Columnar Grains

Effect of the Cooling Rate on the Microstructure of Directionally Solidified Casting (CMSX-4 Ni Superalloy)

The Influence of the Cooling Bores on Crystal Orientation and Lattice Parameter in Single-Crystalline Cored Turbine Blades

Influence of Processing Parameters on the Solidification Behavior of Single-Crystal Cmsx-4 Superalloy