Abstract:Since temperatures of airfoil surfaces in advanced turbine engines are approaching the limit of nickel base superalloys, Nb-Ti-Si base alloys as their potential materials have attracted much attention recently. Nb-Ti-Si base alloys have high melting temperature, suitable densities, good elevated temperature creep strength and acceptable room temperature fracture toughness, therefore, they are expected to be employed in the temperature range of 1200-1450 ℃ as structural materials. Alloying and directional solidification are generally used to obtain a better combination of room temperature fracture toughness with high temperature creep strength and oxidation resistance for an elevated-temperature alloy. In this paper, the master alloy ingot with a nominal composition of Nb20Ti-16Si-6Cr-5Hf-4Al-2B-0.06Y (atomic fraction, %) was prepared by using vacuum consumable arc-melting. The integrally directional solidification of this alloy was conducted in a high vacuum and ultrahigh temperature directional solidification furnace with the use of a ceramic crucible at melt temperature of 2050 ℃. The integrally directionally solidified microstructure, preferred orientation of constituent phases and solid/liquid (S/L) interface morphology at different solidifying rate (2.5, 5, 10,20, 50 and 100 μm/s) for this alloy have been investigated by XRD, SEM and EDS, and the growth mechanism of Nbss/(Nb, X)_5Si_3 (where Nbss denotes Nb solid solution, X represents Ti, Hf and Cr elements) eutectic in it has been discussed. The results show that the directionally solidified microstructure of the alloy is mainly composed of hexagonally cross-sectioned primary (Nb, X)_5Si_3 columns and coupled grown lamellar Nbss/(Nb, X)_5Si_3 eutectic colonies both aligned straight and uprightly along the growth direction. When the solidifying rate varies from 2.5 μm/s to 100 μm/s, the solid/liquid interface of the alloy undergoes an evolution from coarse cellular, fine cellular and finally to cellular dendrite morphologies. Both the average diameter of eutectic cells and lamellar spacing in them decrease with the increase in solidifying rate. The formation of a regular Nbss/(Nb, X)_5Si_3 eutectic morphology is attributable to a large kinetic undercooling and a low fusion entropies of alloy phases.

Effect of Directional Solidification Variables on the Microstructures of Single-Crystal Turbine Blades of Nickel-Based Superalloy

Effect of Directional Solidification Methods on Solid Solution Window in Ni-based Single-Crystal Superalloy

Development of Numerical Simulation in Nickel-Based Superalloy Turbine Blade Directional Solidification

The Effects of Withdrawal and Melt Overheating Histories on the Microstructure of a Nickel-Based Single Crystal Superalloy

Eutectic Microstructure Evolution of Directionally Solidified Nb-Ti-Si Base Ultrahigh Temperature Alloy

Three-Dimensional Dendrite Growth Within the Shrouds of Single Crystal Blades of a Nickel-Based Superalloy

Effect of Withdrawal Rate on the Microstructure and Mechanical Properties of a Novel Monocrystalline CoNi-based Superalloy

Effect of thickness on microstructure of thin-walled nickel-based single-crystal superalloy castings

EFFECT OF SOLIDIFYING RATE ON INTEGRALLY DIRECTIONALLY SOLIDIFIED MICROSTRUCTURE AND SOLID/LIQUID INTERFACE MORPHOLOGY OF AN Nb-Ti-Si BASE ALLOY

INFLUENCE OF WITHDRAWING RATE TRANSITION ON THE PRIMARY DENDRITE ARM SPACING AND MICROSEGREGATION OF DIRECTIONALLY SOLIDIFIED SINGLE CRYSTAL SUPERALLOY DD3

Influence of withdrawal rate on microstructures of blade shaped directionally solidified DZ125 superalloy

Effect of Withdrawal Rate on the Microstructure of Directional Solidified Ni-43Ti-4Al-2Nb-2Hf Single Crystal Alloys

THE EFFECTS OF WITHDRAWAL AND MELT OVERHEATING HISTORIES ON THE MICROSTRUCTURE OF A NICKED-BASED SINGLE CRYSTAL SUPERALLOY

Effect of solidification parameters on the microstructures of a single crystal Ni-based superalloy AM3

Effect of the Withdrawal Rate on the Microstructure and Creep Behavior of the Directionally Solidified Nickel-Based Superalloy

Multiscale Modeling and Simulation of Directional Solidification Process of Ni-Based Superalloy Turbine Blade Casting

Effect of secondary orientation on the microstructures in thin-walled castings of nickel-based single-crystal superalloys

Effect of Withdrawal Rate on Microstructure of Directionally Solidified Ni-45Ti-5Al Alloys

Effect of Solidification Parameters on the Microstructures of Superalloy CMSX-6 Formed During the Downward Directional Solidification Process

Modeling of Unidirectional Growth in a Single Crystal Turbine Blade Casting

Microstructural Evolution of Directionally Solidified Ni-Based Superalloy Dz125 under High Temperature Gradient