Abstract:Liquid fuels are good candidates for combustion-based miniature power sources due to their large specific energy. In this study, combustion characteristics of n-C4H10/air mixtures in a tube (ID = 6 mm) partially filled with wire mesh was experimentally explored over an equivalence ratio of phi = 0.5-1.5. In most cases, partially submerged flames and surface flames were observed on the downstream side of the porous media. An external diffusion flame was established under high inlet velocities for fuel-rich mixtures of 1.2 <= phi <= 1.5. The flame with a center convex started to appear at a certain inlet velocity due to the relatively higher local velocity, which was a result of the rolling up method of the wire mesh. Moreover, a lower extinction limit of 0.1 m/s was achieved over 0.9 <= phi <= 1.2, whereas the blow-off limit rose almost linearly up to 0.8 m/s with the equivalence ratio even on the fuel-rich side. The underlying mechanisms for this tendency were comprehensively analyzed from the preheating effect, heat loss effect, volumetric expansion effect as well as the support effect from the external diffusion flame. Furthermore, for an identical inlet velocity, the wall temperature first rose until phi = 1.1 and then decreased when phi > 1.1. Under a constant equivalence ratio, both the maximum wall temperature and the exhaust gas temperature increased with an increasing inlet velocity. However, for an identical inlet velocity, the exhaust gas temperature at low and moderate inlet velocities remained almost invariable versus the equivalence ratio. This was speculated to be the relatively small variation of heat loss ratio versus equivalence ratio. In summary, these findings enriched the knowledge of n-C4H10/air combustion in small tubes partially filled with porous media.

Experiments on N-Heptane Combustion with Two Types of Catalyst Layouts

Experimental study of premixed n-heptane/air catalytic combustion characteristics in micro-cylindrical tube

Dimensional Effect on Self-Sustaining Catalytic Combustion of N-Heptane in Micro/Meso Tubes

Catalytic combustion of methane, methanol, and ethanol in microscale combustors with Pt/ZSM-5 packed beds

Catalytic Combustion of VOCs on Pt/CuMnCe and Pt/CeY Honeycomb Monolithic Catalysts

Effect of Catalyst Length and Hydrogen Addition on the Combustion Characteristics of N-Butane in A Catalytic Swiss-Roll Combustor

Heterogeneous Reaction and Homogeneous Flame Coupled Combustion Behavior of N-Decane in a Partially Packed Catalytic Bed Combustor

Catalytic Combustion of N-C4h10and DME in Swiss-Roll Combustor with Porous Ceramics

Characteristics of Premixed Catalytic Combustion of Nature Gas

Catalytic Self-Sustaining Combustion of the Alkanes with Pt/ZSM-5 Packed Bed in a Microscale Tube

Methane/Air Fuel-Rich Combustion in a Catalyst Enhanced Two-Layer Porous Media Burner

Combustion of hydrogen–air in catalytic micro-combustors made of different material

A Numerical Investigation on Non-Premixed Catalytic Combustion of CH4/(O2 + N2) in a Planar Micro-Combustor

Numerical simulation of premixed n-heptane/air combustion in micro tube with internal channel optimization

Comparison of catalytic combustion of methane andn-butane in microtube

Experimental Study on Combustion Characteristics of N-C4h10/air Mixtures in a Meso-Scale Tube Partially Filled with Wire Mesh

Investigation on H2/CH4 fueled combustion with partially Pt-loaded porous media

The Surface and Gas-Phase Reactions in Microscale Catalytic Partial Oxidation of N-Butane/air Mixture

Elementary Reaction Modeling and Experimental Characterization on Methane Partial Oxidation within a Catalyst-Enhanced Porous Media Combustor

Combustion characteristics of n-heptane spray combustion in a low temperature reform gas/air environment

Preparation of Monolithic Pt–Pd Bimetallic Catalyst and Its Performance in Catalytic Combustion of Benzene Series