Abstract:Abstract This paper presents 3D Fabry–Pérot (FP) cavities fabricated directly onto cleaved ends of low-loss optical fibers by a two-photon polymerization (2PP) process. This fabrication technique is quick, simple, and inexpensive compared to planar microfabrication processes, which enables rapid prototyping and the ability to adapt to new requirements. These devices also utilize true 3D design freedom, facilitating the realization of microscale optical elements with challenging geometries. Three different device types were fabricated and evaluated: an unreleased single-cavity device, a released dual-cavity device, and a released hemispherical mirror dual-cavity device. Each iteration improved the quality of the FP cavity’s reflection spectrum. The unreleased device demonstrated an extinction ratio around 1.90, the released device achieved 61, and the hemispherical device achieved 253, providing a strong signal to observe changes in the free spectral range of the device’s reflection response. The reflectance of the photopolymer was also estimated to be between 0.2 and 0.3 over the spectrum of interest. The dual-cavity devices include both an open cavity, which can interact with an interstitial medium, and a second solid cavity, which provides a static reference reflection. The hemispherical dual-cavity device further improves the quality of the reflection signal with a more consistent resonance, and reduced sensitivity to misalignment. These advanced features, which are very challenging to realize with traditional planar microfabrication techniques, are fabricated in a single patterning step. The usability of these FP cavities as thermal radiation sensors with excellent linear response and sensitivity over a broad range of temperature is reported. The 3D structuring capability the 2PP process has enabled the creation of a suspended FP heat sensor that exhibited linear response over the temperature range of 20 oC –120 oC; temperature sensitivity of ∼50 pm oC −1 at around 1550 nm wavelength; and sensitivity improvement of better than 9x of the solidly-mounted sensors.

Bessel-like Beams Generated Via Fiber-Based Polymer Microtips

Characterization of White-Light Non-Diffracting Beams Generated Using a Deformable Mirror.

Fabrication of High-Aspect-ratio Structures Using Bessel-beam-activated Photopolymerization

All-Dielectric Fiber Meta-Tip for Generating Bessel and Airy Beams

Polymer Microtip Bridge Between Two Optical Fibers Integrated in a V-Groove

Photopolymer Microtips for Efficient Light Coupling Between Single-Mode Fibers and Small-Core Photonic Crystal Fibers

Generation of Bessel-beam arrays for parallel fabrication in two-photon polymerization

Three-dimensional Fabry–Pérot cavities sculpted on fiber tips using a multiphoton polymerization process

White light Bessel-like beams generated by miniature all-fiber device

Two-Photon Polymerization of Cylinder Microstructures by Femtosecond Bessel Beams

Micro- and Nanofabrication Using Bessel-beam Activated Photopolymerization

Optical Microfibers Integrated with Evanescent Field Triggered Self-Growing Polymer Nanofilms.

Polymer Micro or Nanofibers for Optical Device Applications

Generation of Bessel Beams Via Femtosecond Direct Laser Writing 3D Phase Plates

Stable Generation of Cylindrical Vector Beams with an All-Fiber Laser Using Polarization-Maintaining and Ring-Core Fibers.

Spatial Beam Self-Cleaning in Bi-Tapered Multimode Fibers

Generation of Subwavelength Inverted Pin Beam Via Fiber End Integrated Plasma Structure

Laser-oriented growth of long polymer tip for scanning optical applications

Silt-Beam Shaping Method for Femtosecond Laser Point-by-Point Inscription of Highly Localized Fiber Bragg Gratings with Enhanced Cladding Modes

Generation of nonparaxial self-accelerating beams using pendant droplets

Beam Self-Cleanup by Use of Self-Written Waveguide Generated by Photopolymerization.