Abstract:As power efficiency becomes essential in automotive applications, DC-DC converters are widely employed [1]. However, size and thermal limits have made it challenging to continue using standard CMOS-based converters. Gallium Nitride (GaN) FETs, on the other hand, have a much higher conductivity with small size/capacitance in comparison to silicon FETs, enabling a highly efficient power conversion at high switching frequency (f SW ). However, there are several issues that must be resolved before using GaN in automotive. High f SW incurs larger di/dt and dv/dt transitions which injects high frequency electromagnetic interference (EMI) noise into the input bus. This creates unwanted noise or even a malfunction in a safety-critical system. A bulky input filter can reduce EMI, but it greatly increases size and cost. Several techniques [2-5] are reported to mitigate EMI. Frequency hopping using discrete frequencies is proposed in [2], but cannot spread the frequency evenly to lower the peak noise effectively. Alternatively, a series resistor is typically added at the gate of the GaN FET to slow down the transition [3-4]. However, the switching loss is dramatically increased. To mitigate this, adjustable driving strength is proposed in [5]. Unfortunately, the sensing and driver delays confine its use in low f SW applications, where the switch node rising time is several tens or hundreds of ns. Another issue of high f SW operation is that it causes significant current and voltage spikes due to the parasitics at the drain/source of the high side GaN FET (M H ), which could lead to GaN VDS breakdown or damage on logic-level FETs. Thus, EMI noise suppression and reliable operation of GaN FETs remain as major challenges in realizing high f SW power converters for automotive-use.

A GaN HEMTs Half-Bridge Driver with Bandgap Reference Comparator Clamping for High-Frequency DC-DC Converter.

A 2–10 MHz GaN HEMTs Half-Bridge Driver with Bandgap Reference Comparator Clamping and Dual Level Shifters for Automotive Applications

A GaN-based MHz Active Clamp Flyback Converter with Adaptive Dual Edge Dead Time Modulation for AC-DC Adapters.

A Tri-Slope Gate Driving GaN DC–DC Converter with Spurious Noise Compression and Ringing Suppression for Automotive Applications

25.2 A 10mhz 3-to-40v VIN Tri-Slope Gate Driving GaN DC-DC Converter with 40.5dbµv Spurious Noise Compression and 79.3% Ringing Suppression for Automotive Applications

A 2mhz Constant-Frequency AOT V-2 Buck Converter with Adaptive Dead Time Control for Data Centers

A Digital PWM Controller of MHz Active Clamp Flyback with GaN Devices for AC-DC Adapter.

Design of Low-Inductance Switching Power Cell for GaN HEMT Based Inverter

Ultra-Low Inductance Design for A Gan Hemt Based 3L-Anpc Inverter

High-Frequency Three-Level Gate Driver for GaN HEMT Bridge Crosstalk Suppression

A 400-V Half Bridge Gate Driver for Normally-off GaN HEMTs with Effective dv/dt Control and High dv/dt Immunity

A 1-Mhz ZVS Boost DC-DC Converter with Active Clamping Using GaN Power Transistors

A High-Speed Low Side GaN E-Hemt Driver with Gate Ringing and Overshoot Suppression.

Monolithic GaN-Based Driver and GaN Switch With Diode-Emulated GaN Technique for 50-MHz Operation and Sub-0.2-ns Deadtime Control

A New GaN-Based Device, P-Cascode GaN HEMT, and Its Synchronous Buck Converter Circuit Realization

A Self-clamping Non-synchronous Duty Cycle Control Strategy for Hybrid Clamping Three-level Buck Converter with GaN Devices

Dual Active Bridge Based on High Voltage GaN Device

Comparisons on Different Innovative Cascode GaN HEMT E-Mode Power Modules and Their Efficiencies on the Flyback Converter

Study and Implementation of 600-V High-Voltage Gate Driver IC With the Common-Mode Dual-Interlock Technique for GaN Devices

An Efficient High-Frequency Drive Circuit for GaN Power HFETs

A Monolithic GaN Power Stage with Common-Mode Transient Immunity and Negative Voltage Operation Design for High Frequency Power Converters