Abstract:Titanium and its alloys (especially Ti6Al4V) are widely employed in aerospace and biomedical industry. Wire electric discharge machining is common in practice to machine this difficult-to-cut material. But owing to the thermo-electric nature of the process, it is challenging to have adequate level of surface integrity. This primary concern needs to be addressed as it mainly influences the surface mechanical characteristics. Therefore, the present research aims to address the aforesaid issues using well-known multipass strategy. Understanding the multipass process dynamics and requirements, the potentiality of brass wire diameters was comprehensively examined and explored during WEDM of Ti6Al4V. Considering higher cost, unavailability, environmental hazards, and straightness issues of novel zinc-coated wire electrodes, readily available brass wires provide a cheaper and widely acceptable solution to enhance surface integrity of machined parts if equivalent results can be somehow made possible. For that sake, three different brass wire diameters; 0.15 mm, 0.2 mm, and 0.25 mm have been considered to evaluate their impact on surface roughness, recast layer thickness, overcut, machined surface microhardness, and cutting speed using multipass cutting technique. Experimental results revealed that 0.15 mm uncoated brass wire can produce white layer result equivalent to Topas Plus X wire (Cu core-double Zn-rich layer coating) which outperformed among all zinc-coated wires used in previously published research. Moreover, among different diameter brass wires, surface roughness is improved by 25% using multipass cutting with 0.15 mm diameter in comparison to its counterparts. Scanning electron microscope (SEM) analysis depicts that the said combination reduces recast layer thickness from 39.04 μm to 14.6 μm (~ 1.5 times lesser value). In addition to that, smaller diameter (0.15 mm) provides the maximum cutting rate in rough cuts (which consume maximum machining time) and dimensional accuracy.

Experimental Study on Surface Quality and Machinability of Ti-6Al-4V Rotated Parts Fabricated by Low-Speed Wire Electrical Discharge Turning

Curved Profiles Machining of Ti6Al4V Alloy Through WEDM: Investigations on Geometrical Errors

Experiments of Ti6Al4V manufactured by low-speed wire cut electrical discharge machining and electrical parameters optimization

Effects of Wire Electrical Discharge Finishing Cuts on the Surface Integrity of Additively Manufactured Ti6Al4V Alloy

An in-depth evaluation of surface characteristics and key machining responses in WEDM of aerospace alloy under varying electric discharge environments

Optimization of Process Parameters on Surface Integrity in Wire Electrical Discharge Machining of Tungsten Tool YG15

Machinability and pulse characteristics of Ti-16Al-14Nb (α/β) alloy in wire-electric discharge machining process: A surface integrity study

Performance Analysis of Wire Electrodes on Machining Ti-6Al-4V Alloy using Electrical Discharge Machining Process

Finishing the surface micro-layer of additively manufactured TiAl alloy using electro-thermal discharge assisted post-processing

Materials That Do Not Form Any Defects After WEDM

Machining characteristics and optimization of 10CrNi3Mo alloy steel by WEDM

Investigating Technological Parameters and TiN-Coated Electrodes for Enhanced Efficiency in Ti-6Al-4V Micro-EDM Machining

Evaluation of Wire Electrical Discharge Machining Performance Features on EN AW-6082 T6 Aluminum Alloy and Optimization of Machining Characteristics

Investigation on a Novel Surface Microstructure Wire Electrode for Improving Machining Efficiency and Surface Quality in WEDM

Performance Studies on the Wire Electric Discharge Machining Characteristics of Stellite-6B Superalloys

Characterization of Physical and Mechanical Properties of Tungsten Alloy Surfaces for Electroplasticity-Assisted Dry Cutting Machining

Evaluating Optimal Parameters for Machining Selective Laser Melting Titanium Alloy Using Wire Cut Electrical Discharge Machining

Study on surface evenness of super-high-thickness cutting in high-speed wire electrical discharge machining

Improving Micro-EDM Machining Efficiency for Titanium Alloy Fabrication with Advanced Coated Electrodes

Experimental investigation on the surface quality of WEDM machined 20MnCr5 steel for Gear application

Experimental Study of the Surface Quality of Form-Cutting Tools Manufactured via Wire Electrical Discharge Machining Using Different Process Parameters