Abstract:Enhancing the operational efficacy of electrical discharge machining (EDM) is crucial for achieving optimal results in various engineering materials. This study introduces an innovative solution—the use of coated electrodes—representing a significant advancement over current limitations. The choice of coating material is critical for micro-EDM performance, necessitating a thorough investigation of its impact. This research explores the application of different coating materials (AlCrN, TiN, and Carbon) on WC electrodes in micro-EDM processes specifically designed for Ti-6Al-4V. A comprehensive assessment was conducted, focusing on key quality indicators such as depth of cut (Z), tool wear rate (TWR), overcut (OVC), and post-machining surface quality. Through rigorous experimental methods, the study demonstrates substantial improvements in these quality parameters with coated electrodes. The results show significant enhancements, including increased Z, reduced TWR and OVC, and improved surface quality. This evidence underscores the effectiveness of coated electrodes in enhancing micro-EDM performance, marking a notable advancement in the precision and quality of Ti–6Al–4V machining processes. Among the evaluated coatings, AlCrN-coated electrodes exhibited the greatest increase in Z, the most significant reduction in TWR, and the best OVC performance compared to other coatings and the uncoated counterpart.

What problem does this paper attempt to address?

This paper aims to solve the problem of improving the efficiency in micro - electrical discharge machining (Micro - EDM) of titanium alloy (Ti - 6Al - 4V). Specifically, the research focuses on improving the performance of micro - electrical discharge machining by using WC electrodes with different coating materials such as AlCrN, TiN and carbon. The paper explores the influence of these coating materials on key quality indicators, including cutting depth (Z), tool wear rate (TWR), over - cut amount (OVC) and the surface quality after machining. ### Main problems 1. **Improving machining efficiency**: Titanium alloy (Ti - 6Al - 4V) is difficult to be machined by traditional methods due to its excellent mechanical properties. As an alternative method, micro - electrical discharge machining (Micro - EDM) needs to be further optimized to improve its machining efficiency. 2. **Improving quality parameters**: The research aims to improve the key quality parameters of micro - electrical discharge machining, such as cutting depth (Z), tool wear rate (TWR), over - cut amount (OVC) and surface quality, by using coated electrodes. ### Research methods - **Experimental design**: Micro - electrical discharge machining experiments were carried out on titanium alloy (Ti - 6Al - 4V) using four different electrodes (uncoated WC electrode, TiN - coated electrode, carbon - coated electrode and AlCrN - coated electrode). - **Experimental equipment**: The Hyper 10 micro - electrical discharge machining system was used for the experiments. - **Experimental parameters**: Three input parameters, namely voltage, capacitance and rotational speed, were considered in the experiments and tested under different conditions. ### Key findings - **Cutting depth (Z)**: The coated electrodes significantly increased the cutting depth, among which the AlCrN - coated electrode performed the best. - **Tool wear rate (TWR)**: The AlCrN - coated electrode had the lowest tool wear rate, followed by TiN - and carbon - coated electrodes. - **Over - cut amount (OVC)**: The coated electrodes reduced the over - cut amount in most cases, especially under lower voltage and capacitance conditions. - **Surface quality**: The surface quality after machining with the coated electrodes was improved, especially with the AlCrN - coated electrode. ### Conclusions - Using coated electrodes can significantly improve the efficiency and quality of micro - electrical discharge machining. - The AlCrN - coated electrode performs best in increasing the cutting depth, reducing the tool wear rate and over - cut amount. - Future research should further optimize the selection of coating materials and machining parameters to achieve more efficient micro - electrical discharge machining. Through these studies, the paper provides important theoretical and experimental bases for improving the efficiency and quality of micro - electrical discharge machining of titanium alloy.

Improving Micro-EDM Machining Efficiency for Titanium Alloy Fabrication with Advanced Coated Electrodes

Investigating Technological Parameters and TiN-Coated Electrodes for Enhanced Efficiency in Ti-6Al-4V Micro-EDM Machining

Optimizing micro-EDM with carbon-coated electrodes: A multi-criteria approach

Enhancing EDM performance with multi-objective decision-making using copper-coated aluminum electrodes and TOPSIS methodology for Ti-6Al-4V machining

Multi-criteria decision making for better quality indicators in μ-EDM using TiN-coated WC electrode

Optimization of Machining Process on Coated Tungsten Carbide Electrode Tool and Titanium Alloy Workpiece Using EDM: A Critical Review

Enhancing microhardness and surface integrity of Ti–6Al–4V alloy using WC–Cu composite electrode aided electrical discharge coating

Performance and Microstructure of TiN/Cu EDM Electrodes

An Experimental Study on Processing TC4 with Nano Particle Surfactant Mixed Micro EDM

Effect of Electrode Materials on Different EDM Aspects of Titanium Alloy

Machining efficiency and geometrical accuracy on micro-EDM drilling of titanium alloy

Performance Analysis of Wire Electrodes on Machining Ti-6Al-4V Alloy using Electrical Discharge Machining Process

Experimental Study on the Comparison between Network Microstructure Titanium Matrix Composites and Ti6Al4V on EDM Milling

Editors' Choice—Improving Quality of EDMed Micro-Holes on Titanium via In Situ Electrochemical Post-processing: A Transient Simulation and Experimental Study

Effect of Deposition Parameters on Micromechanical Properties and Machining Performance of CrN Coating for Wet Finish Turning of Ti6Al4V Alloy

Enhancing Surface Integrity in Micro-EDM of Ti-6Al-4V Alloy Adopting Two-Dimensional Ultrasonic Circular Vibration (UCV) Electrode

A Comprehensive Study on Processing Ti-6Al-4V ELI with High Power EDM

Enhancing Tool Performance in High-Speed End Milling of Ti-6Al-4V Alloy: The Role of AlCrN PVD Coatings and Resistance to Chipping Wear

A fundamental study on Ti–6Al–4V's thermal and electrical properties and their relation to EDM productivity

Experimental investigation of the EDM tools coated with nano-alumina film

Research to determine the best value of both Z and OVC in micro-EDM using carbon coated electrode using topsis method