Abstract:Electron beam freeform fabrication (EBF3) additive manufacturing technique has been successfully employed to print the non-weldable Al-5Cu thin-walled parts through an optimized set of process parameters. Post-heat treatment is conducted to engineer the desirable microstructure containing multiple nanostructures, i.e., the nanoscale θ" and θ' precipitates, stacking faulted zones and Al-Cu-Cd clusters, leading to a high-strength Al-5Cu alloy with good ductility. The grain formation mechanisms are revealed via a combinatorial simulation and experimentation. It is shown that EBF3 process can produce three different types of grain microstructures: fully equiaxed, fully columnar, and the mixture. In the layerwise melt pool solidification process, wide partially melted zone is observed to favor the formation of equiaxed grains due to its inheritance characteristic. After solution and aging heat treatment, Al-Cu-Cd nanoclusters (∼ 2 nm in Dia.) are generated, which facilitates the formation of nanoscale stacking faulted zones (∼11 nm). Meanwhile, as heterogeneous nucleation sites, Al-Cu-Cd nanoclusters effectively promote θ'-Al2Cu phase (∼ 19 - 114 nm) precipitation to enable the coexistence with fine θ"-Al3Cu precipitates (∼ 7 - 37 nm). The multiscale microstructure, especially incorporating the newly identified nanoscale stacking faulted zones, activates multiple strengthening mechanisms. Consequently, its tensile properties at room temperature reach an ultimate tensile stress of ∼ 496.5 MPa, yield strength of ∼ 435.7 MPa, and elongation of ∼ 9.6%, which are superior to other as-cast and additively manufactured Al-Cu alloys. This work offers a promising processing route to directly fabricate high-strength near-net-shape Al-Cu alloy parts for the aerospace and automotive industries.

Additive Manufacturing of Fine-Structured Copper Alloy by Selective Laser Melting of Pre-Alloyed Cu-15Ni-8Sn Powder

The mechanical and functional behaviors of Mn–15 wt.%Cu alloy produced by selective laser melting

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Selective Laser Melting of Cu–10Sn–0.4P: Processing, Microstructure, Properties, and Brief Comparison with Additively Manufactured Cu–10Sn

Selective Laser Melting of High Relative Density and High Strength Parts Made of Minor Surface Oxidation Treated Pure Copper Powder

Mechanical Properties and Microstructural Characterization of Cu-4.3 Pct Sn Fabricated by Selective Laser Melting

Microstructure Twinning and Mechanical Properties of Laser Melted Cu-10Sn Alloy for High Strength and Plasticity

Effect of Process Parameters on the Microstructure and Properties of Cu–Cr–Nb–Ti Alloy Manufactured by Selective Laser Melting

Processing Technologies and Properties of Cu-10Sn Formed by Selective Laser Melting Combined with Heat Treatment

Selective laser melting 316L/CuSn10 multi-materials: Processing optimization, interfacial characterization and mechanical property

Microstructure, Mechanical Properties, and Fatigue Fracture Characteristics of High-Fracture-Resistance Selective Laser Melting Al-Ni-Cu Alloys

Additive manufacturing of a high strength Al-5Mg2Si-2Mg alloy: Microstructure and mechanical properties

Additive manufacturing of high strength copper alloy with heterogeneous grain structure through laser powder bed fusion

Hierarchical microstructure and strengthening mechanism of Cu-36.8Fe alloy manufactured by selective laser melting

Densification, Microstructure, and Mechanical Properties of Additively Manufactured 2124 Al–Cu Alloy by Selective Laser Melting

Multiscale microstructure containing nanometer-scale precipitations and stacking faults yields a high-strength Al-5Cu alloy by electron beam freeform fabrication

Achieving high strength in selective laser melting AlSi10Mg alloy by adding microsized pure Cu particles

Additive Manufacturing of Isotropic-Grained, High-Strength and High-Ductility Copper Alloys

Pure copper components fabricated by cold spray (CS) and selective laser melting (SLM) technology

Simultaneous strength and ductility enhancements of high thermal conductive Ag7.5Cu alloy by selective laser melting

Nanotwins-containing microstructure and superior mechanical strength of a Cu‒9Al‒5Fe‒5Ni alloy additively manufactured by laser metal deposition