Abstract:In the field of non-destructive evaluation (NDE) of solid metal materials, it has been a challenge to detect surface and internal defects simultaneously by using a single physical mechanism technique. Conventionally, different testing techniques, in which each one is particularly sensitive to a certain type of defect, are employed to gain full defect information. However, a separated testing method is always a time-consuming and laborious work. Here, we report a magnetoelectric-ultrasonic hybrid transducer and multimodal system for quantitative NDE of metal, which integrates a magnetoelectric composite wrapped with a coil for generating alternating current field and simultaneously measuring magnetic abnormal of surface defects (referred to as ME-ACFM) and a dual-piezoceramic ultrasonic transducer (DP-UT) for generating acoustic pulses and detecting the echo signal of internal defects, respectively. A bipulse signal with different pulse widths is used for excitation of the hybrid transducer, in which one is corresponded to the resonant frequencies of 5 MHz for DP-UT, and another to 122 kHz for ME-ACFM. The huge difference between two resonant frequencies is helpful for restraining signal interference each other. Experimental investigations show that when scanning the tested specimens (standard steel No.45 and aluminum plates), the surface and internal defects information can be obtained simultaneously almost without a dead zone. The surface defect resolutions of 0.1 mm width and 0.1 mm depth, and the inside defect resolution of 2 mm blind hole are obtained; the experimental errors for surface defect (crack) depth up to 5 mm are around 5 %; while experimental errors for ultrasonic depth measurement (with a blind zone of 1.25 mm) is less than 0.63 mm. The proposed hybrid transducer and multimodal system open up a new way for designing multi-physical mechanism based NDEs.

Complicated Defects Detection Based on Hybrid NDT Methods of PECT and EMAT

Composite Defects Evaluation Using the Hybrid NDT Methods of PECT and EMAT

A Hybrid Nondestructive Testing Method of Pulsed Eddy Current Testing and Electromagnetic Acoustic Transducer Techniques for Simultaneous Surface and Volumetric Defects Inspection

Mechanism Hybrid EMAT and Eddy Current Sensing Detection for Surface and Internal Defects NDT

Quantitative Sizing of Compound Location Defects Based on PECT-EMAT Hybrid Testing Methods

Quantifying Hidden Defect In Multi-Layered Structures By Using Eddy Current System Combined With A Scanner

Multiphysics Structured Eddy Current and Thermography Defects Diagnostics System in Moving Mode.

Defect Detection and Identification of Point-Focusing Shear-Horizontal EMAT for Plate Inspection

Physic perspective fusion of electromagnetic acoustic transducer and pulsed eddy current testing in non-destructive testing system

A Composite Approach of Electromagnetic Acoustic Transducer and Eddy Current for Inner and Outer Corrosion Defects Detection

A hybrid nondestructive testing method of pulsed eddy current testing and electromagnetic acoustic transducer techniques based on wavelet analysis

Physical coupling fusion sensing of MFL-EMAT for synchronous surface and internal defects inspection

Composite Sensor of EMAT and ECT Using a Shareable Receiver Coil for Detecting Surface and Bottom Defects on the Steel Plate

Eddy Current Test/ultrasonic Testing Integrative Method for Detecting Sub-Surface Defects in Conductive Structures

Deep Defects Evaluation of Conductive Materials Based on Eddy Current Nondestructive Testing with GMR sensor

Coupling Pulse Eddy Current Sensor for Deeper Defects NDT

A New Method to Evaluate Surface Defects with an Electromagnetic Acoustic Transducer

Application of Hilbert–Huang transform for defect recognition in pulsed eddy current testing

Pulsed Eddy Current Array Imaging Detection Technology Used for Defect Detection

A magnetoelectric-ultrasonic multimodal system for synchronous NDE of surface and internal defects in metal

A Novel Pulsed Eddy Current Inspection Technique for Non-Ferromagnetic Metal Defect Detection