Abstract:A new selective catalytic reduction (SCR) system for captive power plants in the petrochemical industry was analyzed. The key components suitable for the target SCR system were obtained using computational fluid dynamics (CFD) numerical simulation combined with a cold physical model. The structural characteristics of the SCR system were studied, and corresponding design schemes were obtained for the key components, such as the guide plate, the ammonia injection grid (AIG), the static mixer, and the rectifier grille. The distributions of the flue gas velocity and the NH3 concentration within the flue cross-section in front of the first layer catalyst were studied in detail. Synchronously, the pressure loss and the temperature reduction characteristics in the SCR system were also considered. CFD results showed that the average standard deviation of the flue gas velocity was about 11.61%, and the average standard deviation of the NH3 concentration distribution could reach about 3.79% under the five operating conditions. It could be concluded that the uniformity of the flue gas velocity and the NH3 concentration distribution within the above flue cross-section was guaranteed by comparing to the design standard of 15% and 5%, respectively. It was further found that the maximum pressure loss between the inlet and the first layer catalyst was about 106.64 Pa, and the temperature reduction characteristic of the entire SCR system could be maintained within ±0.01 °C, which indicated that no extreme adverse effect arose due to the introduce of the key components. The cold physical model experiment was accordingly conducted to verify the reliability of the above CFD results. The cold physical model experiment results showed that the average standard deviation of flue gas velocity was about 8.82%, and the average standard deviation of NH3 concentration distribution could reach about 4.21%. The maximum biases for the standard deviations of the flue gas velocity and the NH3 concentration distribution were approximately 4.83% and 1.18% under the five operating conditions. Based on the good agreement of the research results via the two different methods, the designed key components of a new SCR system could be confirmed to be feasible, which would benefit the deNOx performance of the SCR system.

Process Identification of the SCR System of Coal-Fired Power Plant for De-Nox Based on Historical Operation Data.

Model Predictive Control Case Study: Selective Catalytic Reduction (scr) System in Coal-Fired Power Plant

Sustainable Integration of Stream Power Plant Couple of Contaminant Emissions Reduction Technology

Selective Catalytic Reduction (Scr) Modeling Using Parallel Way Of Identification

The Parameter Identification Method of Steam Turbine Nonlinear Servo System Based on Artificial Neural Network

Recursive Least Square Method Based Parameter Identification of Steam Turbine Digital Electric-Hydraulic Governing System

Application Of Recursive Least Squares Method For Parameter Identification Of Deh Governing System

Fractional-Order Modeling and Identification for an SCR Denitrification Process

Adaptive Internal Model Control of SCR Denitration System Based on Multi-Objective Optimization

Enhancement of SCR denitrification control strategy considering fluegas temperature fluctuation: Fundamental principle and performance evaluation

Control of Selective Catalytic Reduction Systems Using Feedback Linearisation

Two-timescale Nonlinear Model Predictive Control for Flexible Operation of Coal-Fired Power Plant with Post Combustion CO2 2 Capture System

Dynamic Modeling of NOX Emission in a 660 MW Coal-Fired Boiler with Long Short-Term Memory

Prediction and Control of the Nitrogen Oxides Emission for Environmental Protection Goal Based on Data-Driven Model in the SCR De-Nox System

Multi‐model predictive control of SCR flue gas denitrification system in coal‐fired power plant based on kernel fuzzy c‐means clustering and integrated model

Design and Verification of Key Components of a New Selective Catalytic Reduction System in a Petrochemical Captive Power Plant

Identification-based Real-Time Optimization and Its Application to Power Plants

Closed-Loop Control Strategy and State Estimator for Diesel Engine SCR After-Treatment System

MLD–MPC for Ultra-Supercritical Circulating Fluidized Bed Boiler Unit Using Subspace Identification

A temporal discretization and spatial integration SCR model with dual temperature-related parameters

Application of an Improved State Feedback Control in the Selective Catalytic Reduction Denitrification Systems of Coal Power Units Under Variable Load Conditions