Abstract:This paper presents a level-crossing successive-approximation-register (LC-SAR) hybrid analog-to-digital converter (ADC) that combines an LC ADC with an SAR ADC, which may be used for Internet of Things (IoT) random sparse event scenarios. The sampling frequency of a traditional LC ADC is usually proportional to the maximum instantaneous rate of change of the input signal; therefore, a higher input signal frequency inevitably leads to higher system power consumption. However, the proposed hybrid ADC uses the input level difference between the two moments before and after level-crossing detection, thereby ensuring a higher conversion precision and lower power consumption, even at higher input signal frequencies. Compared with traditional LC ADC or SAR ADC, the proposed hybrid ADC combines the ultralow-power advantage of LC ADC with the high-precision advantage of SAR ADC in converting IoT data with sparse characteristics such as ECG, EEG, and brain potential. The LC-SAR hybrid ADC is designed with a 0.18 μm CMOS process and consumes 4.34 μW at a 1.8 V supply voltage, achieving an SNDR of 67.41 dB and a bandwidth of 20 kHz. The spectrum analysis result was 10.85 ENOB when the input sinusoidal signal was 14.975 kHz. When inputted with an ECG signal, the system power consumption was as low as 0.49 μW. Furthermore, the proposed hybrid ADC obtained a good figure of merit, with FoMw and FoMs reaching 58.8 fJ/conv.steps and 164 dB, respectively. Compared to a conventional uniform sampling ADC, approximately 80% of the power savings and an 8x compression ratio can be achieved in physiological signal acquisition applications.

A 1-to-1-khz, 4.2-to-544-nw, Multi-Level Comparator Based Level-Crossing ADC for IoT Applications.

A 10-Bit 250-KS/s 1.24-uW SAR ADC for IoT Sensors with Energy-Efficient Comparator.

A Threshold Control Technique for CMOS Comparator Design

A 1V 5-bits Low Power Level Crossing ADC with OFF state in idle time for bio-medical applications in 0.18um CMOS

A 61-nW Level-Crossing ADC With Adaptive Sampling for Biomedical Applications

A 77.2-Db SNDR SAR ADC with a Segmented Comparator Logic Based on Compensatory SA Latch for FIA

A Low-Power Inverter-Based ΣΔ Analog-to-digital Converter for Audio Applications

A 10-Bit 16-Ms/s Ultra Low Power SAR ADC for IoT Applications

A 62.2db SNDR Event-Driven Level-Crossing ADC with SAR-Assisted Delay Compensation Loop for Time-Sparse Biomedical Signal Acquisition.

A 0.49–4.34 μW LC-SAR Hybrid ADC with a 10.85-Bit ENOB and 20 KS/s Bandwidth

A 1-V 560-Nw SAR ADC with 90-Db SNDR for IoT Sensing Applications

An Information-Aware Adaptive Data Acquisition System Using Level-Crossing ADC with Signal-Dependent Full Scale and Adaptive Resolution for IoT Applications.

An Ultra-Low Power Fixed-Window Level Crossing ADC for ECG Recording

A 0.9V 12-Bit 200-Ks/s 1.07µw SAR ADC with Ladder-Based Reconfigurable Time-Domain Comparator

A Low Power Cyclic ADC Design for a Wireless Monitoring System for Orthopedic Implants

A 1.2V 62.2dB SNDR SAR-Assisted Event-Driven Clockless Level-Crossing ADC for Time-Sparse Signal Acquisition

A 0.2-Mv 20-Mhz 600-Μw Comparator

78 Nw Ultra-Low-power 17 Ks/s Two-Step-successive Approximation Register Analogue-to-digital Converter for RFID and Sensing Applications

Fully Digital Second-order Level-crossing Sampling ADC for Data Saving in Sensing Sparse Signals

Design of an Ultra-Low Power SAR ADC for Biomedical Applications

A 65.5-Db SNDR 8.1–11.1-Nw ECG SAR ADC with Adaptive-Latching OSC-Based Comparator and DAC Calibration