Abstract:This paper presents a level-crossing successive-approximation-register (LC-SAR) hybrid analog-to-digital converter (ADC) that combines an LC ADC with an SAR ADC, which may be used for Internet of Things (IoT) random sparse event scenarios. The sampling frequency of a traditional LC ADC is usually proportional to the maximum instantaneous rate of change of the input signal; therefore, a higher input signal frequency inevitably leads to higher system power consumption. However, the proposed hybrid ADC uses the input level difference between the two moments before and after level-crossing detection, thereby ensuring a higher conversion precision and lower power consumption, even at higher input signal frequencies. Compared with traditional LC ADC or SAR ADC, the proposed hybrid ADC combines the ultralow-power advantage of LC ADC with the high-precision advantage of SAR ADC in converting IoT data with sparse characteristics such as ECG, EEG, and brain potential. The LC-SAR hybrid ADC is designed with a 0.18 μm CMOS process and consumes 4.34 μW at a 1.8 V supply voltage, achieving an SNDR of 67.41 dB and a bandwidth of 20 kHz. The spectrum analysis result was 10.85 ENOB when the input sinusoidal signal was 14.975 kHz. When inputted with an ECG signal, the system power consumption was as low as 0.49 μW. Furthermore, the proposed hybrid ADC obtained a good figure of merit, with FoMw and FoMs reaching 58.8 fJ/conv.steps and 164 dB, respectively. Compared to a conventional uniform sampling ADC, approximately 80% of the power savings and an 8x compression ratio can be achieved in physiological signal acquisition applications.

A 61-nW Level-Crossing ADC With Adaptive Sampling for Biomedical Applications

A 62.2db SNDR Event-Driven Level-Crossing ADC with SAR-Assisted Delay Compensation Loop for Time-Sparse Biomedical Signal Acquisition.

A Low-Power Inverter-Based ΣΔ Analog-to-digital Converter for Audio Applications

A 1-to-1-khz, 4.2-to-544-nw, Multi-Level Comparator Based Level-Crossing ADC for IoT Applications.

A 1V 5-bits Low Power Level Crossing ADC with OFF state in idle time for bio-medical applications in 0.18um CMOS

A 1.2V 62.2dB SNDR SAR-Assisted Event-Driven Clockless Level-Crossing ADC for Time-Sparse Signal Acquisition

A Low Power Level-Crossing ADC for Wearable Wireless ECG Sensors.

Fully Digital Second-order Level-crossing Sampling ADC for Data Saving in Sensing Sparse Signals

An Ultra-Low Power Fixed-Window Level Crossing ADC for ECG Recording

A 0.49–4.34 μW LC-SAR Hybrid ADC with a 10.85-Bit ENOB and 20 KS/s Bandwidth

Design of an Ultra-Low Power SAR ADC for Biomedical Applications

A 0.9V 12-Bit 200-Ks/s 1.07µw SAR ADC with Ladder-Based Reconfigurable Time-Domain Comparator

A 0.6-V 94-Nw 10-Bit 200-Ks/s Single-Ended SAR ADC for Implantable Biosensor Applications

A 7.6-Nw 1-Ks/s 10-Bit SAR ADC for Biomedical Applications

A 12.9-ENOB 50.6 Fj/conv.step Time-Amplitude Aligned Level-Crossing SAR ADC

A 0.6-V 38-Nw 9.4-ENOB 20-Ks/s SAR ADC in 0.18-&Lt;formula Formulatype="inline"><tex Notation="TeX">$\mu{\rm M}$</tex> </formula> CMOS for Medical Implant Devices

Event-driven Analog-to-digital Converter for Ultra Low Power Wearable Wireless Biomedical Sensors

A 0.6 V 100 KS/s 8–10 B Resolution Configurable SAR ADC in 0.18 Μm CMOS

A 65.5-Db SNDR 8.1–11.1-Nw ECG SAR ADC with Adaptive-Latching OSC-Based Comparator and DAC Calibration

A 5.8 nW 9.1-ENOB 1-kS/s Local Asynchronous Successive Approximation Register ADC for Implantable Medical Device

A 1.2 V 600 Nw 12-Bit 2 Ks/s Incremental ADC for Biosensor Application