Abstract:Vertical wall surfaces with obstacles present a serious challenge for wall-climbing robots. Owing to their limitations in overcoming obstacles, these types of robots have not been commercialized yet. Several ideas on novel designs and precise control have been suggested; however, further research is required to achieve enhanced robot capabilities in overcoming obstacles. Specifically, the use of dry adhesive methods by wall-climbing robots to climb over obstacles present tremendous challenges. This study introduces the design of a new linkage-type, wall-climbing robot, based on dry adhesion, for uneven vertical surfaces. Based on a four-bar mechanism, repeated walking is achieved via a single actuator. The robot's most important feature is the linkage design used for climbing over obstacles, which has been adopted from rover running patterns. The symmetric linkage design renders the robot adaptable to uneven surfaces with a compliant motion. Additionally, flat dry adhesives were used for the attachment mechanism. The design parameters were determined based on kinematic and static analyses, and certain important issues in linkage-type wall-climbing robot designs were addressed. The robot's performance was verified using experiments, whereby it was able to climb up and go down stairs with maximum stair heights of 15 mm (equal to 0.6% of the robot's height) during open-loop vertical walking. We expect that the linkage design can extend the accessible area of the wall-climbing robot. This study introduces the design of a new linkage-type, wall-climbing robot, based on dry adhesion, for uneven vertical surfaces. Based on a four-bar mechanism, repeated walking is achieved via a single actuator. The robot's most important feature is the linkage design used for climbing over obstacles, which has been adopted from rover running patterns. The symmetric linkage design renders the robot adaptable to uneven surfaces with a compliant motion. Additionally, flat dry adhesives were used for the attachment mechanism. The design parameters were determined based on kinematic and static analyses, and certain important issues in linkage-type wall-climbing robot designs were addressed. The robot's performance was verified using experiments, whereby it was able to climb up and go down stairs with maximum stair heights of 15 mm (equal to 0.6% of the robot's height) during open-loop vertical walking. We expect that the linkage design can extend the accessible area of the wall-climbing robot. (C) 2018 Elsevier Ltd. All rights reserved.

A Paper-Based Wall-Climbing Robot Enabled by Electrostatic Adhesion

A Wall-Climbing Robot Using Gecko-Inspired Dry Adhesives and Underactuated Modular Connecting Mechanism

A Bio-inspired Wall-climbing Robot with Claw Wheels and Adhesive Tracks

Research on a wall climbing robot based on electrostatic adhesion

Hybrid electrostatic and elastomer adhesion mechanism for wall climbing robot

Analysis and Optimization of the Wall-Climbing Robot with an Adsorption System and Adhesive Belts

Wall Climbing Robot Using Electrostatic Adhesion Force Generated by Flexible Interdigital Electrodes

Design, Modeling and Experimentation of a Biomimetic Wall-climbing Robot for Multiple Surfaces

A gecko inspired wall-climbing robot based on electrostatic adhesion mechanism

DESIGN AND TESTING OF A WALL-CLIMBING ROBOT WITH UNDER-ACTUATED FORCE ADJUSTING MECHANISM

Design and Development of Wall Climbing Robot

A Biomimetic Wheel-Track Wall-Climbing Robot Based on Rolling Adsorption Mechanism

A Multi-Mode Biomimetic Wall-Climbing Robot

Design, Simulation and Experimentation of a Biomimetic Wall-Climbing Robot with Tracked Spines

Electrostatic-motor-driven electroadhesive robot

Development of a wheeled wall‐climbing robot with an internal corner wall adaptive magnetic adhesion mechanism

Design and Study of a Biomimetic Wall-Climbing Robot with Spine Wheels and a Vacuum Suction Cup.

A Pressing Attachment Approach for a Wall-Climbing Robot Utilizing Passive Suction Cups

Survey on Bioinspired Adhesive Methods and Design and Implementation of A Multi-Mode Biomimetic Wall-Climbing Robot.

Grappling Claws for a Robot to Climb Rough Wall Surfaces: Mechanical Design, Grasping Algorithm, and Experiments.

AnyClimb-II: Dry-adhesive Linkage-Type Climbing Robot for Uneven Vertical Surfaces