Abstract:A normal composite wall panel is a structural component composed of polystyrene insulation boards and concrete surface layers reinforced with steel wire mesh. It can be entirely prefabricated in a factory or constructed with the concrete surface layers cast on-site. A novel prefabricated monolithic concrete–polystyrene panel composite wall panel (CPC wall panel) is proposed in this study. The CPC panel features a middle part that is prefabricated in the factory while the reinforced concrete regions at its two side ends are cast on-site. To evaluate the seismic performance of the wall panel, 18 CPC specimens were designed, manufactured, and quasi-statically tested, through which the structural behaviors, failure mode, and load-bearing capacity were studied. In addition, the influences of the height-to-width ratio and the vertical compressive stress level on the seismic performance of the CPC panels were also investigated. The test results showed that the connectors spaced at 400 mm × 500 mm could ensure the concrete layers on both sides of the polystyrene board worked collectively under seismic conditions. When subjected to lateral loads, the interface between the newly poured concrete and the existing concrete exhibited good bonding. Moreover, the failure mode of the CPC wall panel was largely correlated to the height-to-width ratio that, for specimens having four steel bars of 12 mm diameter and a height-to-width ratio greater than 1, the flexural failure was initially developed, followed by diagonal shear failure. In specimens with a height-to-width ratio of 1, flexural and diagonal shear failures occurred almost simultaneously. For specimens with a height-to-width ratio of less than 1, the final diagonal shear failure was predominant. The longitudinal reinforcing bars at the two ends of the CPC panels could effectively improve their lateral load-bearing capacity, with the enhancement influenced by the height-to-width ratio, the vertical load applied to the wall panel, and the cross-sectional area of the steel bars. In practice, the lateral load-bearing capacity of the CPC panel can be conservatively evaluated using the calculation method of the reinforced concrete shear walls. Finally, the ductility of the CPC specimens was affected by the height-to-width ratio and the axial compressive stress level, such that the specimens with a larger height-to-width ratio and lower axial compressive stress exhibited better ductility.

Pseudo-dynamic Tests on Masonry Residential Buildings Seismically Retrofitted by Precast Steel Reinforced Concrete Walls

EXPERIMENTAL STUDY OF A MASONRY BUILDING RETROFITTED INTEGRALLY BY PRE-FABRICATED RC PANELS

Pseudo-dynamic testing of hybrid frame with steel beams bolted to CFT columns

Seismic performance of shear-critical prefabricated reinforced masonry shear walls with innovative vertical joint connections

Experimental Validation on Seismic Performance of a Monolithic Precast RC Shear Wall Structure with Novel Connections

Performance of Double-Skin Composite Walls with Re-Entrant Profiled Faceplates under Eccentric Compression

Experimental study of reinforced concrete shear wall structure with low reinforcement ratio retrofitted by exterior strengthening method

Experimental Study on Seismic Performance of Prefabricated Monolithic Concrete–Polystyrene Panel Composite Wall Panels

Experimental and Analytical Studies of Prefabricated Composite Steel Shear Walls under Low Reversed Cyclic Loads

Seismic performance of a novel partial precast RC shear wall with reserved cast-in-place base and wall edges

Investigation on Seismic Behavior of a Novel Precast Shear Wall System with Different Infill Wall Constructions

Seismic Performance of Unreinforced Masonry Walls with Various Retrofitting Methods

Seismic performance of a novel partly precast RC shear wall with double precast edge members and a central T-shape CIP member

Experimental study on seismic performance of T‐shaped partly precast reinforced concrete shear wall with grouting sleeves

Experimental and Numerical Study on the Seismic Performance of Prefabricated Reinforced Masonry Shear Walls

Seismic performance and parametric study of precast reinforced concrete Shear Wall structure with indirect‐lapping joints

Experimental Study on Seismic Behaviour of an Unreinforced Precast Wall-Slab Structure Based on UHPC Sandwich Panels

Mechanical performance of prefabricated lightweight steel-foamed ceramsite concrete wall panels: Experimental and theoretical investigations

Seismic performance of a new type of precast shear walls with non-connected vertical distributed reinforcement

In-Plane Strengthening Effect of Prefabricated Concrete Walls on Masonry Structures: Shaking Table Test

Lightly reinforced concrete walls in formwork blocks for the combined seismic and energy retrofit of masonry structures