Abstract:A normal composite wall panel is a structural component composed of polystyrene insulation boards and concrete surface layers reinforced with steel wire mesh. It can be entirely prefabricated in a factory or constructed with the concrete surface layers cast on-site. A novel prefabricated monolithic concrete–polystyrene panel composite wall panel (CPC wall panel) is proposed in this study. The CPC panel features a middle part that is prefabricated in the factory while the reinforced concrete regions at its two side ends are cast on-site. To evaluate the seismic performance of the wall panel, 18 CPC specimens were designed, manufactured, and quasi-statically tested, through which the structural behaviors, failure mode, and load-bearing capacity were studied. In addition, the influences of the height-to-width ratio and the vertical compressive stress level on the seismic performance of the CPC panels were also investigated. The test results showed that the connectors spaced at 400 mm × 500 mm could ensure the concrete layers on both sides of the polystyrene board worked collectively under seismic conditions. When subjected to lateral loads, the interface between the newly poured concrete and the existing concrete exhibited good bonding. Moreover, the failure mode of the CPC wall panel was largely correlated to the height-to-width ratio that, for specimens having four steel bars of 12 mm diameter and a height-to-width ratio greater than 1, the flexural failure was initially developed, followed by diagonal shear failure. In specimens with a height-to-width ratio of 1, flexural and diagonal shear failures occurred almost simultaneously. For specimens with a height-to-width ratio of less than 1, the final diagonal shear failure was predominant. The longitudinal reinforcing bars at the two ends of the CPC panels could effectively improve their lateral load-bearing capacity, with the enhancement influenced by the height-to-width ratio, the vertical load applied to the wall panel, and the cross-sectional area of the steel bars. In practice, the lateral load-bearing capacity of the CPC panel can be conservatively evaluated using the calculation method of the reinforced concrete shear walls. Finally, the ductility of the CPC specimens was affected by the height-to-width ratio and the axial compressive stress level, such that the specimens with a larger height-to-width ratio and lower axial compressive stress exhibited better ductility.

Experimental Study on Seismic Behaviour of an Unreinforced Precast Wall-Slab Structure Based on UHPC Sandwich Panels

Experimental and theoretical study on seismic behavior of a new UHPFRC sandwich wall and wall-wall joint

Experimental and Theoretical Study on Flexural Behaviour of a New UHPC Sandwich Slab

Seismic performance of precast concrete sandwich walls with bolt-steel plate connection

Seismic behavior of a new type of precast concrete shear wall using UHPC connections at boundary elements

Shaking table tests and seismic assessment of a full-scale precast concrete sandwich wall panel structure with bolt connections

Seismic performance of novel bolt-connected precast concrete walls strengthened by UHPC

Experimental Study on Seismic Behavior of a Novel RC Slab- SC Wall Joint Based on UHPC and Rebar - Steel Plate Lap Splices

Experimental Validation on Seismic Performance of a Monolithic Precast RC Shear Wall Structure with Novel Connections

Experimental Study on Seismic Performance of Prefabricated Monolithic Concrete–Polystyrene Panel Composite Wall Panels

Seismic performance of a new type of precast shear walls with non-connected vertical distributed reinforcement

Experimental and Numerical Study on Seismic Performance of Precast Concrete Hollow Shear Walls

Experimental study and efficient shear-flexure interaction model of reinforced concrete shear walls with UHPC boundary columns

Global Experimental Response of a Three-Story, Full-Scale Precast Concrete Shear Wall Structure with Reinforcing Bars Spliced by Grouted Couplers

Study on the global bidirectional seismic behavior of monolithic prefabricate concrete shear wall structure

Mechanical performance of prefabricated lightweight steel-foamed ceramsite concrete wall panels: Experimental and theoretical investigations

Seismic performance of a novel partly precast RC shear wall with double precast edge members and a central T-shape CIP member

An experimental study of the seismic behaviour of precast concrete shear walls with bolted-plate connections

New modular precast composite shear wall structural system and experimental study on its seismic performance

Experiment Study on Seismic Behavior of Squat UHPC Shear Walls Subjected to Tension-Shear Combined Cyclic Load

Seismic performance of a novel partial precast RC shear wall with reserved cast-in-place base and wall edges