Abstract:A normal composite wall panel is a structural component composed of polystyrene insulation boards and concrete surface layers reinforced with steel wire mesh. It can be entirely prefabricated in a factory or constructed with the concrete surface layers cast on-site. A novel prefabricated monolithic concrete–polystyrene panel composite wall panel (CPC wall panel) is proposed in this study. The CPC panel features a middle part that is prefabricated in the factory while the reinforced concrete regions at its two side ends are cast on-site. To evaluate the seismic performance of the wall panel, 18 CPC specimens were designed, manufactured, and quasi-statically tested, through which the structural behaviors, failure mode, and load-bearing capacity were studied. In addition, the influences of the height-to-width ratio and the vertical compressive stress level on the seismic performance of the CPC panels were also investigated. The test results showed that the connectors spaced at 400 mm × 500 mm could ensure the concrete layers on both sides of the polystyrene board worked collectively under seismic conditions. When subjected to lateral loads, the interface between the newly poured concrete and the existing concrete exhibited good bonding. Moreover, the failure mode of the CPC wall panel was largely correlated to the height-to-width ratio that, for specimens having four steel bars of 12 mm diameter and a height-to-width ratio greater than 1, the flexural failure was initially developed, followed by diagonal shear failure. In specimens with a height-to-width ratio of 1, flexural and diagonal shear failures occurred almost simultaneously. For specimens with a height-to-width ratio of less than 1, the final diagonal shear failure was predominant. The longitudinal reinforcing bars at the two ends of the CPC panels could effectively improve their lateral load-bearing capacity, with the enhancement influenced by the height-to-width ratio, the vertical load applied to the wall panel, and the cross-sectional area of the steel bars. In practice, the lateral load-bearing capacity of the CPC panel can be conservatively evaluated using the calculation method of the reinforced concrete shear walls. Finally, the ductility of the CPC specimens was affected by the height-to-width ratio and the axial compressive stress level, such that the specimens with a larger height-to-width ratio and lower axial compressive stress exhibited better ductility.

Shaking table tests and seismic assessment of a full-scale precast concrete sandwich wall panel structure with bolt connections

Experimental Study on Seismic Behaviour of an Unreinforced Precast Wall-Slab Structure Based on UHPC Sandwich Panels

Seismic performance of precast concrete sandwich walls with bolt-steel plate connection

Shaking table test of fabricated concrete shear wall structure and study on damage mechanism of strong earthquake

Seismic performance of a new type of precast shear walls with non-connected vertical distributed reinforcement

An exhaustive research and analysis on seismic performance of prefabricated concrete shear wall structure

New modular precast composite shear wall structural system and experimental study on its seismic performance

Seismic Performance of the Pre-Fabricated Steel Frame Infilled with AAC Wall Panels and Their Joint Connection: Full-Scale Shaking Table Test

Seismic Performance of a Full-Scale Two-Story Reinforced Concrete Frame with Shale Sintered Wallboards Tested on a Shake Table

Experimental Investigation of the Seismic Performance of a Novel Bolt-Assembled Precast Panel Building Structure

Experimental investigation of seismic response of precast concrete panels with castellated keys support pillar connections under in-plane cyclic loading

An experimental study of the seismic behaviour of precast concrete shear walls with bolted-plate connections

Tests on seismic behavior of pre-cast sandwich concrete wall panel with cast-in-site end columns

Experimental Validation on Seismic Performance of a Monolithic Precast RC Shear Wall Structure with Novel Connections

Experimental comparisons of repairable precast concrete shear walls with a monolithic cast-in-place wall

Experimental Study on Seismic Performance of Prefabricated Monolithic Concrete–Polystyrene Panel Composite Wall Panels

Experimental and Numerical Study on Seismic Performance of Precast Concrete Hollow Shear Walls

Seismic performance of precast concrete frame with energy dissipative cladding panel system: Half-scale test and numerical analysis

Experimental and theoretical study on seismic behavior of a new UHPFRC sandwich wall and wall-wall joint

Investigation on Seismic Behavior of a Novel Precast Shear Wall System with Different Infill Wall Constructions

Study on the global bidirectional seismic behavior of monolithic prefabricate concrete shear wall structure