Abstract:A normal composite wall panel is a structural component composed of polystyrene insulation boards and concrete surface layers reinforced with steel wire mesh. It can be entirely prefabricated in a factory or constructed with the concrete surface layers cast on-site. A novel prefabricated monolithic concrete–polystyrene panel composite wall panel (CPC wall panel) is proposed in this study. The CPC panel features a middle part that is prefabricated in the factory while the reinforced concrete regions at its two side ends are cast on-site. To evaluate the seismic performance of the wall panel, 18 CPC specimens were designed, manufactured, and quasi-statically tested, through which the structural behaviors, failure mode, and load-bearing capacity were studied. In addition, the influences of the height-to-width ratio and the vertical compressive stress level on the seismic performance of the CPC panels were also investigated. The test results showed that the connectors spaced at 400 mm × 500 mm could ensure the concrete layers on both sides of the polystyrene board worked collectively under seismic conditions. When subjected to lateral loads, the interface between the newly poured concrete and the existing concrete exhibited good bonding. Moreover, the failure mode of the CPC wall panel was largely correlated to the height-to-width ratio that, for specimens having four steel bars of 12 mm diameter and a height-to-width ratio greater than 1, the flexural failure was initially developed, followed by diagonal shear failure. In specimens with a height-to-width ratio of 1, flexural and diagonal shear failures occurred almost simultaneously. For specimens with a height-to-width ratio of less than 1, the final diagonal shear failure was predominant. The longitudinal reinforcing bars at the two ends of the CPC panels could effectively improve their lateral load-bearing capacity, with the enhancement influenced by the height-to-width ratio, the vertical load applied to the wall panel, and the cross-sectional area of the steel bars. In practice, the lateral load-bearing capacity of the CPC panel can be conservatively evaluated using the calculation method of the reinforced concrete shear walls. Finally, the ductility of the CPC specimens was affected by the height-to-width ratio and the axial compressive stress level, such that the specimens with a larger height-to-width ratio and lower axial compressive stress exhibited better ductility.

Seismic Performance of a Full-Scale Two-Story Reinforced Concrete Frame with Shale Sintered Wallboards Tested on a Shake Table

Seismic Behavior of Composite Shear Walls Incorporating Concrete-Filled Steel and FRP Tubes As Boundary Elements

Seismic Performance of the Pre-Fabricated Steel Frame Infilled with AAC Wall Panels and Their Joint Connection: Full-Scale Shaking Table Test

Shaking table tests and seismic assessment of a full-scale precast concrete sandwich wall panel structure with bolt connections

Research on Seismic Performance of Framework with New SIP Filled Wallboard

Seismic performance of a new type of precast shear walls with non-connected vertical distributed reinforcement

Experiments and Numerical Simulations on the Seismic Performance of Steel-Frame Composite Wallboard Shear Walls

Experimental Study on Seismic Performance of Fabricated Steel Foamed Concrete T-Shaped Wallboard

Shake table tests on a full-scale six-storey cold-formed thin-walled steel-steel plate shear wall structure

Investigation on Seismic Behavior of a Novel Precast Shear Wall System with Different Infill Wall Constructions

In-Plane Strengthening Effect of Prefabricated Concrete Walls on Masonry Structures: Shaking Table Test

Experimental Validation on Seismic Performance of a Monolithic Precast RC Shear Wall Structure with Novel Connections

Simulation of shake‐table test for a two‐story low‐damage concrete wall building

Shake table tests on the traditional column-and-tie timber structures

Seismic behavior of prefabricated concrete filled steel tube-bordered monolayer reinforced shear wall

Experimental Study on Seismic Performance of Prefabricated Monolithic Concrete–Polystyrene Panel Composite Wall Panels

Experimental Study on Seismic Performance of Composite Shear Wall with Horizontal Connection and Frame

Experimental and Numerical Study on Seismic Performance of Precast Concrete Hollow Shear Walls

Seismic performance evaluation of an infilled rocking wall frame structure through quasi-static cyclic testing

Experimental study on seismic performance of new-type fabricated shear wall with mortar connection

Seismic performance of prefabricated wall panels with sliding joints for reinforced concrete frames