Abstract:This research focuses on the influence of silicon alloys in hot-rolled steel strips. The steel used in the study was obtained from a hot rolling process with different silicon contents of 0.01, 0.1, 0.2, and 0.3 wt.%. The as-received oxide scale on the hot-rolled steel surface was completely removed by SiC paper and re-oxidized in a horizontal furnace with an atmosphere of 17% H2O-N2 at temperatures of 600°C, 650°C, and 700°C for 10 seconds. An investigation of scale adhesion can be done using a tensile testing machine with a CCD camera. The adhesion of the oxide scale to the steel surface was recorded on video. The oxide phase was examined by means of X-ray diffraction (XRD). The microstructure and thickness of the oxide scale were examined by a scanning electron microscope (SEM) with energy-dispersive X-ray spectroscopy (EDS). The results indicated that all steels studied produced oxide scales that consisted of hematite (Fe2O3) and magnetite (Fe3O4), which contained iron (Fe). The scale thickness tends to increase with increasing temperature, while thickness decreases with increasing Si content in steel. The oxide scale adhesion was indicated by the strain initiating the first spallation during tensile load. The results showed that the strain initiating the first scale spallation tends to decrease with increasing temperature, while scale adhesion increases with increasing Si content in steel. The mechanical adhesion of the oxide scale to the steel substrate was considered in terms of energy. The results indicate that the scale adhesion of steel with 0.3 wt.% Si was higher than that in another sample. It was possible that the presence of an oxide that contains Si at the scale-steel interface, which encourages scale adhesion. The mechanical adhesion energy of the oxide scale was shown in the range of 2-20 J/m2. The qualitative assessment of scale adhesion in terms of strain initiating the first spallation and mechanical adhesion energy suggested the good adhesion behavior of scale grown in the hot-rolled steel with 0.3 wt.% Si. This result indicates that scale formed on steel with a high silicon content tends to be difficult to remove. There was a need to control the Si content in the hot-rolled steel in a satisfactory way to save energy during the de-scale process.

Influence of Oxide Scales on the Corrosion Behaviors of B510L Hot-Rolled Steel Strips

Effect of Oxide Scale Microstructure on Atmospheric Corrosion Behavior of Hot Rolled Steel Strip

Experimental Study on Adhesion of Oxide Scale on Hot-Rolled Steel Strip

The Structure Change and Corrosion Protectivity of the Oxide Scale on An SS400 Hot-rolled Steel Plate

Effect of Hot-Rolled Oxide Scale on Dry/Wet Cyclic Corrosion Behavior of Q370qNH Steel in Simulated Industrial Atmosphere Environment

Microstructural Study and Residual Stress Measurement of a Hot Rolling Work Roll Material During Isothermal Oxidation

High-temperature Oxidation Behavior and Scale Morphology of Si-containing Steels

High-Temperature Oxidation and Subscale Morphology of Si Containing Steels

Characterization of Oxide Scales Formed on Plain Carbon Steels in Dry and Wet Atmospheres and Their Eutectoid Transformation from FeO in Inert Atmosphere

Influence of Silicon on Oxidation and Adhesion of Oxide Scale on Hot-Rolled Steel Strips

Oxidation Kinetics and Spallation Model of Oxide Scale during Cooling Process of Low Carbon Microalloyed Steel

Comparative Study of Structure and Pickling Characteristics of Oxide Scale Formed on Strips Produced by TSCR and Conventional Process

ISIJ International, Vol. 47 (2007), No. 9, pp. 1329–1334

Effect of microstructure and microtexture evolution of oxide layer over J82B steel on mechanical descaling properties

Oxide scale characterization of ferritic stainless steel and its deformation and friction in hot rolling

Effect of post-annealing on the oxidation behavior of hot rolled ODS-FeCrAl steel in liquid lead

Numerical Simulation of Oxide Scales Evolution During Hot Strip Rolling

Influence of Si Content on Selective Oxidation and Oxide Scale Phase Transition During Hot-Rolled Coiling

The effect of oxide scale of stainless steels on friction and surface roughness in hot rolling

Comparison of Corrosion Scales Formed on Ko8oss and N8o Steels in Co2/H2s Environment

Isothermal Structure Transformation and Kinetics Behavior of Oxide Scale on Low Carbon Steel