Abstract:Cu/ZnO catalysts with varied Cu/(Cu + Zn) molar ratios were prepared by a facile solid-state method. The Cu/(Cu + Zn) molar ratio displayed a significant effect on the oxygen vacancy formation of the calcined catalysts, thereby influencing the CuO–ZnO interaction and the reducibility of CuO. The Cu/(Cu + Zn) molar ratio also exhibited a significant effect on Cu0 surface area, oxygen vacancy, the ratio of ZnO(002) plane to ZnO(100) plane, as well as the basicity and acidity of the reduced catalysts, thereby affecting the catalytic performance for low-temperature methanol synthesis from syngas containing CO2. The correlations of methanol space time yield (STY) versus the physicochemical characteristics of Cu/ZnO catalysts were studied. The catalyst with equal amounts of Cu and Zn displayed the best catalytic activity owing to higher Cu0 surface area, more oxygen vacancy and ZnO(002) plane, as well as more moderately basic sites.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c18600?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c18600</a>.Reaction equipment; Cu 2p and Zn 2p XPS spectra of the calcined catalysts; correlation between the maximum reduction temperature and Ovacancy/Olattice ratio; Cu 2p and Zn 2p XPS spectra of the reduced catalysts; Cu LMM Auger spectrum of CZ-R-0.5 catalyst; reaction route of high-temperature ICI process for methanol synthesis; new reaction route of methanol synthesis at low temperatures using methanol itself as a catalytic promoter; variation of total carbon conversion of CZ-R-0.5 catalyst with time on stream; XRD patterns of the CZ-R-0.5 sample before and after reaction; and results of comparison with CO2 and without CO2 (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c18600/suppl_file/am0c18600_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Study of the Effect of Zn, Sn, and Pb Additives on the Direct Mechanochemical Synthesis of Tetramethoxysilane in the Presence of CuCl and CuO Catalysts

Promoter Effects of Zn and Sn in the Direct Synthesis of Methylchlorosilanes

Single-atom Sn-Zn pairs in CuO catalyst promote dimethyldichlorosilane synthesis.

Enhancing Dimethyldichlorosilane Production in Rochow-Müller Reaction by Adding ZnO-Sn-P Co-promoter in CuO/SiO2

Process characteristics of Cu-based catalyst in direct synthesis of methylchlorosilanes

Optimization of Conditions for Preparation of ZSM-5@silicalite-1 Core–shell Catalysts Via Hydrothermal Synthesis

Effect Of Cucl Particle Size On The Reduction Reaction By Silicon In Preparation Of Contact Mass Used For Methylchlorosilane Synthesis

A Bi-component Cu Catalyst for the Direct Synthesis of Methylchlorosilane from Silicon and Methyl Chloride

From silicon to silicones without dimethyldichlorosilane. Direct green mechanochemical synthesis of methylmethoxysilanes from silicon and dimethyl ether.

Doubling the life of Cu/ZnO methanol synthesis catalysts via use of Si as a structural promoter to inhibit sintering

Complete Liquid Phase Preparation and Characterization of CuZnAlSi Catalysts for DME Synthesis in Slurry Reactor

Effect of Copper Content on the Direct Process of Organosilane Synthesis from Silicon and Methyl Chloride

Basic evidences for methanol-synthesis catalyst design

Effect and Role of Al Addition in the Direct Synthesis Reaction of Methylchlorosilane Monomer

A study of Cu-Mn/SiO2 catalysts for methanol synthesis

Deciphering the promoting mechanism of SnO2 to Cu2O in the Rochow-Müller reaction

Synthesis of methylchlorosilane by direct process and its gas chromatographic analysis

Structure–Performance Correlations over Cu/ZnO Interface for Low-Temperature Methanol Synthesis from Syngas Containing CO 2

Mesosynthesis of ZnO-silica composites for methanol nanocatalysis

Modification of CuCl catalyst used in the direct synthesis reaction of methyl chlorosilane monomer

Xps Study on Cuznal Catalysts Prepared by Different Methods for Direct Synthesis of Dimethyl Ether