Abstract:The processing conditions were varied during the production of polycarbonate-based composites with the multiwalled carbon nanotubes (MWCNTs) Baytubes® C150 P (Bayer MaterialScience AG, Leverkusen, Germany), by melt mixing with an extruder on a laboratory scale. These included the screw design, rotation speed, throughput, feeding position and MWCNT content. Particular attention was paid to the shortening of the MWCNT length as a function of the conditions mentioned. It was found that there is a correlation between the applied specific mechanical energy (SME) during the melt mixing process and MWCNT dispersion, which was quantified by the agglomerate area ratio of the non-dispersed nanotubes based on optical microscopic analysis. The higher the SME value, the lower this ratio, which indicates better dispersion. Above an SME value of about 0.4 kWh/kg, no further improvement in dispersion was achieved. The MWCNT length, as measured by the quantitative analysis of TEM images of the MWCNTs dissolved from the composites, decreased with the SME value down to values of 44% of the original MWCNT length. At a constant loading of 3 wt.%, the tensile strength and tensile modulus were almost independent of the SME, while the elongation at break and notched impact strength showed an increasing trend. The variation in the feeding position showed that feeding the MWCNTs into a side feeder led to slightly better electrical and mechanical properties for both types of MWCNTs studied (Baytubes® C150 P and NanocylTM NC7000 (Nanocyl S.A., Sambreville, Belgium)). However, feeding into the hopper led to better CNT dispersion with Baytubes® C150 P, while this was the case with NanocylTM NC7000 when feeding into the side feeder. The screw profile had an influence on the dispersion, the MWCNT length and the electrical resistance, but only to a small extent. Distributive screws led to a greater shortening of the MWCNT length than dispersive screws. By varying the MWCNT content, it was shown that a greater MWCNT shortening occurred at higher loadings. Two-stage masterbatch dilution leads to stronger shortening than composite production with direct MWCNT incorporation.

Continuous film casting of polycarbonate/single‐walled carbon nanotubes composites with ultrasound‐assisted twin‐screw extruder: Effect of screw configuration

Influence of Processing Parameters During Ultrasound Assisted Extrusion on the Properties of Polycarbonate/carbon Nanotubes Composites

Nylon 66/clay nanocomposite structure development in a twin screw extruder

Ultrasonic Twin Screw Compounding of Polypropylene with Carbon Nanotubes, Graphene Nanoplates and Carbon Black

Effect of high‐shear mixing by twin‐screw extruder on the dispersion and homogeneity of polyacrylonitrile/carbon nanotube composite solution

Influence of Extrusion Screw Speed and CNT Concentration on the Mechanical and EMI Properties of PC/ABS Based Nanocomposites

Influence of Twin Screw Extrusion Conditions on MWCNT Length and Dispersion and Resulting Electrical and Mechanical Properties of Polycarbonate Composites

Modification of carbon nanotubes using poly(vinylidene fluoride) with assistance of supercritical carbon dioxide: the impact of solvent

Influence of Carbon Nanotube Coatings on Carbon Fiber by Ultrasonically Assisted Electrophoretic Deposition on Its Composite Interfacial Property.

Producing Superior Composites by Winding Carbon Nanotubes Onto A Mandrel under A Poly(Vinyl Alcohol) Spray

New Processing Method to Fabricate High-Performance Carbon-Nanotube/Polyvinyl Alcohol Composite Films

Continuous spinning of a single-walled carbon nanotube-nylon composite fiber

Influence of High Loading of Cellulose Nanocrystals in Polyacrylonitrile Composite Films

Ultrasound-Assisted Extrusion Compounding of Nano Clay/Polypropylene Nano Compounds

Preparation of flexible, highly conductive polymer composite films based on double percolation structures and synergistic dispersion effect

Simultaneous Ultrasonication‐assisted Internal Mixing to Prepare MWCNTs‐filled Epoxy Composites with Increased Strength and Thermal Conductivity

Experimental study on the continuous preparation of high‐performance thermal conductivity CNTs/EG/SSBR composite based on the shear and elongation flow fields with the assistance of the silanization reaction

Dramatically Improved Dielectric Properties of Polymer Composites by Controlling the Alignment of Carbon Nanotubes in Matrix

A Novel Continuous Carbon Nanotube Fiber/carbon Composite by Electrified Preform Heating Chemical Vapor Infiltration

The Injected Foaming Study of Polypropylene/Multiwall Carbon Nanotube Composite with In Situ Fibrillation Reinforcement

Effects of Carbon Nanofibers on Crystalline Structures and Properties of Ultrahigh Molecular Weight Polyethylene Blend Fabricated Using Twin‐screw Extrusion