Abstract:Purpose This study aims to form composite solid lubricant coatings on the surface of bearing steel, which can significantly improve the tribological properties of thrust cylindrical roller bearings (TCRBs). Phosphating films possess microscopic porosity that typically needs to be sealed with oil, grease or wax. Due to its unique crystal structure, the phosphating film itself also exhibits a certain degree of lubricity. In this study, solid lubricants are used to fill the pores of the phosphating film. By combining the phosphating film with solid lubricants, lubrication and wear reduction can be achieved. Design/methodology/approach In this study, the surfaces of the shaft washer (WS) and seat washer (GS) were treated with zinc-phosphating. Subsequently, a solid lubricant solution (polytetrafluoroethylene [PTFE], MoS 2 and graphite) was sprayed onto the phosphated samples at concentrations of 1 , 2 and 3 g/L. The porous and adsorptive nature of the phosphating film was used to embed the solid lubricant particles into the film, thus forming a composite lubrication layer containing solid lubricants on the surface of the bearing steel. Findings The addition of solid lubricant materials has shown significant potential in reducing wear losses compared with phosphated samples without such additives. Increasing the amount of solid lubricant added can facilitate the formation of a transfer film, which further enhances the protective properties. However, it is important to note that excessive amounts of solid lubricant material can contribute to seizure, leading to increased wear losses of the cage and a higher average coefficient of friction (ACOF).By spraying a PTFE solution with a concentration of 2 g/L, the lowest ACOF and cage wear loss were achieved, resulting in reductions of 60.5% for the ACOF and 89.4% for the cage wear loss. Similarly, when spraying a graphite solution with a concentration of 3 g/L, the lowest wear losses for GS and WS were observed, with reductions of 51.7% for GS wear loss and 38.9% for WS wear loss. Originality/value The combination of the phosphating film and solid lubricants aims to achieve lubrication and wear reduction, providing a new approach to wear-resistant technology for TCRBs. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0231/

Investigation on MoS 2 and Graphite Coatings and Their Effects on the Tribological Properties of the Radial Spherical Plain Bearings

Compaction of Hydrophobic Molybdenum Disulfide Coatings for Promoting Tribological Behaviors on Engineering Steel

Tribological performance of Mn3(PO4)2 coating and PC/MoS2 coating in Rolling–Sliding and pure sliding contacts with gear oil

Investigation on the Tribological Behaviors of As-Sprayed Al2O3 Coatings Sealed with MoS2 Dry Film Lubricant

Preparation and tribological properties of Mo/MoS2-Pb-PbS composite films

Research on friction and wear behaviors of different solid lubricant coatings on aluminum-based piston skirts

Investigation of the Tribological Properties of Two Different Layered Sodium Silicates Utilized As Solid Lubrication Additives in Lithium Grease

Novel green lubricated materials: Aqueous PAI-MoS2-graphite bonded solid lubricating coating

Comparative tribological and friction behaviors of oil-lubricated manganese phosphate conversion coatings with different crystal sizes on AISI 52100 steel

Tribological performance of MoS2 coating on slipper pair in axial piston pump

An investigation of fretting wear behaviors of bonded solid lubricant coatings

Preparation and tribological properties of multi-layer graphene/silicon dioxide composites-based solid lubricant coatings at elevated temperatures

MICROSTRUCTURES AND WEAR-RESISTANCE BEHAV-IORS OF FERROUS SULFIDE COATINGS

Tribological Performance of MoS 2 Coating on Slipper Pair in Axial Piston Pump

Effect of ZnO on tribological properties of MoS2 dry film lubrication coatings

Effect of composite solid lubricant coatings on the tribological performance of thrust cylindrical roller bearings

Tribological properties and bearing application of Mo-based films in space environment

Tribological performance analysis of nano-FeS films deposited on the surface of bearing steel

Atomic oxygen resistance and tribological performance of a self-stratifying Polydimethylsiloxane-polyamide-imide/molybdenum disulfide lubricating coating

Long-Term Investigations of Different Bearing Configurations at Solid-Lubricated Rolling Bearings

Strengthening mechanism of different morphologies of nano-sized MSH on tribological performance of phosphate/MoS2 bonded solid lubricating coatings