Abstract:High-energy ball milling represents an efficient process for producing composite powders consisting of ceramic particles dispersed in a metallic matrix. However, collision events, plastic deformations, and cold welding during the milling lead to a flake or block-like shape of the resulting composite powders. Further consolidation of such irregularly shaped powders by powder bed-based additive manufacturing technologies can be challenging because of their low flowability and low bulk density. In this work, different approaches, including milling process parameters (speed, process control agent atmosphere) and post-treatments (mechanical and thermal), are investigated on their suitability to influence the particle shape, especially concerning the roundness of the composite powders consisting of the aluminum alloy AlSi10Mg with 5 vol% SiC and Al2O3 reinforcement. It is found that milling with menthol as a process control agent leads to the finest composite powder compared to other milling parameters, with the lowest particle roundness of 0.39 (initial powders 0.84). No success in rounding the milled composite powder could be achieved through mechanical post-treatment in a planetary ball mill. On the other side, the thermal spraying of, e.g., SiC reinforced AlSi10Mg powder resulted in a 77–82% relative roundness. A remarkable change in the microstructure and the shape of the composite powders could also be observed after heat treatment in tube furnaces at a temperature above the melting point of AlSi10Mg. The best result in terms of improved roundness (relative to around 85%) was obtained for Al2O3 reinforced at 600 °C. A further increase of the temperature to 700 °C resulted in a moderate coarsening of powders with Al2O3 and extensive sintering of powders with SiC, presumably due to a different distribution inside the matrix.

Fabrication of Spherical Alsi10mg Powders by Radio Frequency Plasma Spheroidization

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Study on the Flow Properties of Ti-6Al-4V Powders Prepared by Radio-Frequency Plasma Spheroidization

Fabrication of Spherical Thermal-Conductive Silicon Nitride Powder

Exploring Microstructure, Wear Resistance, and Electrochemical Properties of AlSi10Mg Alloy Fabricated Using Spark Plasma Sintering

The influence of NH 3 plasma treatment on microstructure and mechanical property of AlSi10Mg alloy fabricated by selective laser melting

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Fabrication of spherical W–ZrC powder for additive manufacturing by spray granulation combined with plasma spheroidization

Spheroidization of borosilicate glass powder by RF induction coupled plasma

Fabrication of Al‐Si Alloys by Microwave Sintering

Radio Frequency Plasma Spheroidization of Alumina as a Feedstock Material for Ceramic 3D Printing

Study on the RF Inductively Coupled Plasma Spheroidization of Refractory W and W-Ta Alloy Powders

Manufacturing and properties evaluation of Al2O3/ZrO2 granules derived from sodium alginate gelation

Structure and Strength of Aluminum with Sub-Micrometer/micrometer Grain Size Prepared by Spark Plasma Sintering

Influencing the Size and Shape of High-Energy Ball Milled Particle Reinforced Aluminum Alloy Powder

Fabrication of spherical WC-Co powders by radio frequency inductively coupled plasma and a consequent heat treatment

A Novel Method for Preparation of High Strength Hollow Spherical Silicon Dioxide By Plasma Technology

Experimental investigation on powder processing and its flow properties of AlSi10Mg alloy with niobium carbide for additive manufacturing

Production of Spherical TiAl Alloy Powder by Copper-Assisted Spheroidization

Laser powder bed fusion processing of plasma atomized AlSi10Mg powder: Surface roughness and mechanical properties modification

Role of powder particle size on laser powder bed fusion processability of AlSi10mg alloy