Abstract:Powder metallurgy (PM) technology is expected to provide a promising strategy for the cost-effective and highly efficient utilization of spherical Ti–6Al–4V powders with particles size of large than 150 μm to reduce material waste. However, how to overcome the problem of low sinterability and poor ductility of coarse lamellar microstructures of large-diameter spherical powders are still remains a significant challenge. In this study, Ti–6Al–4V alloys were prepared by spark plasma sintering (SPS) at different sintering temperatures with plasma rotating electrode process (PREP) large-diameter spherical powders (∼156 μm). The microstructure evolution, grain structure, mechanical properties and fracture mechanisms were systematically investigated. Results demonstrate that the acicular martensite structure inside the unmelted particles changed to a uniform and fine α/β lamellar microstructure with the increased sintering temperature. Consequently, the Ti–6Al–4V alloys exhibit excellent strength-ductility at 925 °C. (ultimate tensile strength of 881 MPa and elongation up to 14.8 %). Fundamentally, the excellent strength-ductility was attributed to the uniform and dense fine α/β lamellar structure that enhanced the effective bearing area during deformation. The stacked dislocations at the α/β phase interface provided high strength. In addition, the high-density α/β phase interface in the matrix reduced the mean free path of the dislocation, which resulted in a high strain hardening rate of the high-density geometrically necessary dislocations (GNDs) and delayed the premature fracture. The intergranular brittle fracture mode of the alloys changed to the ductile fracture mode. These findings have important implications for recycling super-large diameter spherical powders.

Production of Spherical TiAl Alloy Powder by Copper-Assisted Spheroidization

Preparation of Spherical Porous and Spherical Ti6Al4V Powder by Copper-Assisted Spheroidization Method

A Method for the Preparation of Spherical Titanium Powder for Additive Manufacturing

Preparation of ti-al based nanophase composite powder by mechanical alloying

Preparation of Ti/Al based nanophase composite powder by mechanical alloying

Manufacturing a TiAl Alloy by High-Energy Ball Milling and Subsequent Reactive Sintering

Mechanically Alloyed Amorphous Ti50(Cu0.45Ni0.55)44–xAlxSi4B2 Alloys with Supercooled Liquid Region

Investigation on Fabrication and Microstructure of Ti–6Al–4V Alloy Hollow Spheres by Powder Metallurgy

Preparation of fine-grains TiAl alloys by mechanical alloying and spark plasma sintering

Research Progress on TiAl Alloy Prepared by Powder Metallurgy

One-step Synthesis of Spherical Al3Ta Alloy Powder by Electrolyzing Solid Ta2O5 in Molten Fluorides

A Novel Ultrasonic Atomization Process For Producing Spherical Metal Powder

A Study on Spherical Particles in Al65Cu20Fe15 Alloy Prepared by Arc Melting

Formation of Spheroidal Microstructure in Semi-solid State of Al-4.8Si-2.8Cu-0.5Mg Aluminium Alloy

Synthesis of Tial Based Alloy by Mechanical Milling, Warm Pressing and Reactive Sintering

Achieving excellent strength-ductility combination in Ti–6Al–4V alloy by spark plasma sintering technology using large-diameter PREP spherical powder

Porous TiAl alloys fabricated by sintering of TiH 2 and Al powder mixtures

Study on the Fabrication of Porous TiAl Alloy Via Non-Aqueous Gel Casting of a TiH2 and Al Powder Mixture

Research Progress of Powder Metallurgical Technology for Intermetallic Titanium Aluminide

Mechanical synthesized nanocrystalline Ti/Al composite powders as precursor for Ti/Al alloy via reactive sintering

Preparation and Characterization of TiB2/Al3Ti/Al2O3 Composite Nano-powder