Abstract:In recent years, with the advances in integrated circuit and electronic chips, as well as the development of MEMS technology, the total power density of the system increases. Therefore, requirements for high performance cooling methods become more urgent. As water being the working fluid, microchannels have been integrated into the LTCC substrate, which has applied to the thermal management of the heat flux of 1 ~ 4W/cm 2 . But it still cannot meet the conditions of high heat density. In this article, two methods are used to improve the thermal performance of the substrate, with a kind of low-melting point metal alloy (GaIn 20 ) as the working fluid in the channels (with 400μm in width) and adding via holes in the area of microchannels. And by means of three-dimensional numerical simulation, Reynolds numbers, flow rate and the maximum temperature of substrate on heat transfer performance of LTCC substrate are simulated with software COMSOL Multi-physics. The cooling performance of the LTCC substrate with microchannels was experimentally measured under different flow rate of deionized water when heat flow density of the heating modules is 1w/cm 2 and 2w/cm 2 . While comparing to the simulation of heat transfer performance under the same circumstances, relative error of the maximum temperature do not exceed 8%. Simulation results show that the module is to be effective. With the low-melting liquid metal alloys GaIn 20 and deionized water that used as the working fluid respectively, heat transfer performance was simulated. Comparatively analyze both thermal performance under similar dynamic conditions with heat resource different heat flux, the results show that when the heat flux increases to 5W / cm 2 , the cooling performance of deionized water as the fluid is not ideal, but the low-melting metal is able to cool the maximum temperature of the substrate to 354K with GaIn 20 flowing at a rate of 70ml/min when the heat the fluid density increases up to 10W / cm 2 . While adding via holes to the substrate, the maximum temperature is able to be reduced to 357K below with GaIn 20 flowing at flow rate of 70ml/min when the heat flux density increases up to 30W / cm 2 .

Optimization of heat transfer of microchannels in LTCC substrate with via holes and liquid metal

Experimental Investigation on Optimization of the Performance of Gallium-Based Liquid Metal with High Thermal Conductivity As Thermal Interface Material for Efficient Electronic Cooling

Heat transfer performance of microchannels in LTCC substrate

Microchannel water cooling for LTCC based microsystems

Fluid Flow and Heat Transfer Characteristics of Liquid Cooling Microchannels in LTCC Multilayered Packaging Substrate

Simulation on Heat Transfer of Microchannels and Thermal Vias for High Power Electronic Packages

Design and Analysis of Microchannel for the Thermal Management of Multi-stacked LTCC Laminates

Flow and Heat Transfer Performances of Liquid Metal Based Microchannel Heat Sinks under High Temperature Conditions

Computational Study and Optimization of Laminar Heat Transfer and Pressure Loss of Double-Layer Microchannels for Chip Liquid Cooling

Hybrid Mini/Micro-Channel Heat Sink Using Liquid Metal and Water As Coolants

Simulation of fluid flow and heat transfer in microchannel cooling for LTCC electronic packages

Design of Microchannel Heat Sink Using Topology Optimization for High Power Modules Cooling

Embedded microfluidic cooling with compact double H type manifold microchannels for large-area high-power chips

Numerical Investigation of Fluid Flow and Heat Transfer in High-Temperature Wavy Microchannels with Different Shaped Fins Cooled by Liquid Metal

A 3D Micro-Channel Cooling System Embedded in LTCC Packaging Substrate.

Experimental Investigation of Liquid Metal Alloy Based Mini-Channel Heat Exchanger for High Power Electronic Devices

Design, integration and performance analysis of a lid-integral microchannel cooling module for high-power chip

Design of Practical Liquid Metal Cooling Device for Heat Dissipation of High Performance Cpus

Suitability of Embedded Liquid Cooling and Heat Generation for Chips

Temperature uniformity analysis and multi-objective optimization of the microchannel heat sink with cavities under longitudinal vortex flow

Investigation of cooling performance of micro-channel structure embedded in LTCC substrate for 3D micro-system